Finalizing cabin and interior

Here are some pics of recent progress belowdeck.  Currently (June 20th) I am finishing the cabintop, fitting the Dorade boxes and hatch shroud, and remedying the PO's repair of the bow in preparation to paint the hull and fit the stem fitting.

Hanging locker

Aft of the port-side rode locker, opposite of the microwave and toolbox, was planned this locker.  In framing it I realized there was much more space than I expected.  As it is now, it has several bins to hold shoes, balled-up t-shirts and cottons, various personal effects as well as 12" worth of clothes on hangers.  Shirts and coats will fold onto the floor; but it's much better than having nowhere to hang clean clothes at all.

The first photo shows the after bulkhead, where the plumbing is (which necessitated the locker being delineated from the bunk space in the first instance).  The 1-1/2" vented loop is for the holding-tank pumpout; the smaller standpipe is the holding-tank vent which goes to a 3/4" through-hull in the hull.  The wiring will go to a 3-gang panel over the head sink for the lights.  The little 1-1/4" elbow shown coming through the wall is the head-sink drain, going to its trap and thence to 3/4" hose for the seacock.

I don't know if I've said this before but, when fitting plumbing traps to boat sinks, one should always make them turn forward or aft first and then inboard only after they have gone downwards, to ensure sufficient drainage on either tack.  (This says nothing about the shape of the basin which may retain water to leeward of the drain; but that can't be helped unless you have a basin more steeply sloped than the usual angle of heel.)

The other pic shows the forward side of the same locker.  The "Get A Grip' placard came from a hook-and-loop strap display at the West Marine store where I worked; I thought it was hysterical and swiped it from the trash when the sale was over and cut it to a minimal size (and then spilled acetone on it, causing the blur).  It's been in the boat for about 6 years and by now deserves a place as decor.

 

This locker will get covered with a canvas curtain to keep water out, as the foredeck hatch is directly overhead.

The vertical door-jamb pieces probably need some cleaner way of terminating outboard of the sill-- I'll look to that later.

Main cabin, aft

These two pics show the back corners of the main cabin, the electrical panel to port and the galley and bookcase to starboard.  Among other things can be seen my re-use of the (1974) teak fiddle rails that were originally fitted to the outboard hull shelves over the settees.  This wasn't an easy task since the cabin, as molded, is not symmetrical-- the port-side bulkhead was fully one inch wider than the starboard side, as is evident since the vertical posts are keyed to the hatch's opening.  The solution lay in justifiying the space between two spindles on the center of the opening and then ensuring that no spindles are too close to the ends.  I think one of them is a little off, by less than 1/8", but you won't be able to tell (and one strict rule of Diana is that no one is permitted to visit this boat with a ruler in hand!).

In the spirit of complete disclosure: the cheek piece at the after end of the overhead cabinet (where the radio goes) is teak, not mahogany!  It came from a very weathered piece in a trash bin and I didn't recognize it till I'd sanded it down and applied varnish.  Oh, well-- at least both sides are the same (from the same board in fact).

On neither side is the cap fitted to the top of the divider bulkhead.  I've been getting impatient about getting this stuff varnished and installed, just so it doesn't clutter up the cabin and inhibit other progress (as it's all been doing for too many years) and so I screwed this stuff into place as it is now.  I'll fit the cap pieces after I finish the after side of these bulkheads (more on that-- and a surprise! --later).

I haven't had the motivation to build the drawers for the galley yet and so the cabinet bulkhead beside the ladder is still missing.

I don't go in for the trite little piracy fetish so many yachties favor; but the skull-and-crossed-bones can cooler is in tribute to my late cousin Peter, who co-founded Raider Yacht (for which this was a logo).  So it shall remain on the boat.

  

Other stuff

Here is a cool pic of the foredeck hatch.  It lets in some phenomenal light-- you can read by it in the saloon, even during a rain, even with the other hatch closed.  I've been saying all along that if this project is taking far too long, at least I get to spend my days with gorgeous bits of varnished Honduras mahogany; and here's an example.

The stick holds up the hatch because the hardware isn't on yet.  The cords are what secures it down against wind, rattles and motion.

The green tape is a sign reminding me which end goes forward.  Remember that the hatch frame is cut from the base on the deck, to ensure that they fit together, before the base is installed.  Even with a rectangle it matters which way it goes.

Below is a pic of the (too dusty!) sink in the head.  The cabinet lift-out panels are not painted and so not fitted yet.  The leaning board is the divider, not screwed in, that will hold a shelf in the forward locker.

The portion of counter after of the seam in the fiddle hinges up for access to a 4-inch-deep bin (the original bin over the footwell of the settee berth.  The astute will recall that this idea was my contribution to this boat's design in 1972; see here).

I messed up the trim stick that goes atop the blue countertop along the forward bulkhead and it hasn't been remade and installed yet.  In (typical) impatience I had just "eyeballed" the angle against the fiddle and cut it; and it's too wrong to be tolerable.

I could have tugged the wire loom a little more tightly into the upper shelf, under the window, for this pic; but there's still wiring to be run in it.

Don't say anything about the after cheek piece protruding below the upper fiddle rail while the forward one remains even.  This is an oversight and will be remedied!  The trick deserving the credit is in the making of both cheek pieces, one wide and one narrower, so that they align with the locker face which, which like the sink-counter face, is parallel to the centerline.  How else would it have been done?

And this allows the curtain rods to be fastened to the cheek pieces, more or less parallel horizontally.  My mom, the accomplished seamstress, is currently making the curtains for these hull windows.

Main saloon

Lastly here is a pic of the saloon bulkhead after I fitted the cheek pieces along the top.  This had been long unfinished because I just didn't know a way of making it all in one piece; and then (in the shower, as so often happens) I conceived of the positively brilliant notion of making each side in two pieces.  I wanted some straight line to avoid emphasizing the roundness of the cabintop in here; and here is my solution: an ogee curve descending to a second cheek piece and a further horizontal line.  Together these just about cover the ragged fiberglass tape (though not quite) and represent an apparently-structural deck beam in conjunction with the compression post (the true structural deck beam is on the forward side of the bulkhead, requiring the horizontal door header).

In keeping with the conceit of having these pieces represent a real deck beam, I deliberately made these of Phillipine (lauan), not Honduras; so they appear greyer, darker, a little greener than the footwell trim and table cleat mounted lower on the bulkhead.  The cheek pieces to cover the gap between bulkhead and cabinside will be of (thinner) Honduras.

All of these pieces, as well as those on the forward side of this bulkhead, are "permanently" installed now.  If the white or varnish requires any more touching-up, it'll be done with them in situ.

I should have reinstalled the arched door header here; but in fitting the cheek pieces I ran one screw into the bulkhead, thinking it would be covered by the door header, and just missed; so I have to fill it and paint it again first.

Dave saw this and commented on my practice of simply screwing these pieces into place without concern for hiding the screw heads behind plugs or multiple cleats, saying it was just like what Uncle Joe would have done.  I took that as a high compliment, as I have long admired Uncle Joe's clearheaded sense about what's least complicated being the most aesthetically pleasant... but I really meant it all this way to be able to remove all these pieces for varnishing (and revarnishing.  As I always say, 'It's never the last coat of varnish!').

I have a really cool idea for after I paint the fiberglass around the companionway hatch (where the centerline is indicated, top of photo); but I won't share that till it's been done.  Stay tuned.

* * *

More on the inner-staysail bulkhead

In this pic I have painted the bulkhead but have not attached the fuzzy hull liner, the bow-locker door, or the chain-locker doors.   The hull liner is the roll wrapped in cardboard paper lying on the bunktop.

I am not going to paint the faux-teak bow-locker bulkhead, just for old-times' sake, to show the original fabric of the boat as-built.  The small holes in the stem are awaiting the fitting of the stem fitting (see here).

In this pic also can be seen my method for securing the forward hatch: small cord tied to eyestraps on the hatch, the same as my dad did on our 31' plywood yawl in 1962.

The fiddles on the hull shelves, port and starboard, are made high enough to make bins.  These will hold sailbags (it's a small boat!) and other stuff the way the old ones (about 2" high) never would have done.  Above, as though a facia covering the toerail bolts, will go a similar board to hold hooks from which sail bags, fenders, dock lines and other things can be hung.  As such, this space becomes a bona-fide forepeak, nothing like what's found on even much, much larger yachts.

The varnished board down the center of the underside of the deck is, in this pic, just sort of stuck there.  It is meant to catch the bolts and backing plates of the foredeck cleat, the inner-forestay's attaching plate, and the anchor winch.

I am not happy about the gaps along the top of the chain-locker bulkheads (to port and starboard here) against the underside of the deck but will leave the fitting of some varnished trim for some later date! 

* * *

Inner-forestay support

This pertains to the pole-lift/inner staysail idea I've had for a while.  The blog post is here: http://dianaofburlington.blogspot.com/2012/08/internal-pole-lift.html

In fitting an inner forestay, even if it's a detachable one, the foredeck needs to be reinforced.  Though I've filled all the rotten core adequately, the deck alone won't support something that amounts to a chainplate and may be called upon, in a catastrophe, to support the rig as the only surviving headstay.  So I decided upon a "horse", a structure going athwartships at this point.  Here is my original drawing (on the piece of plywood I would use for the crossmember/deck beam).

Below is shown the initial structure, two short little bulkheads in the forepeak, aligned with a couple of sticks.  The stick under the starboard-side shelf is propping up the shelf from its as-built position, as it was both angled downwards inboard and also too low.  The cleat on the forward bulkhead (what used to be the rode locker)  is aligning the two shelves more or less evenly; though the starboard-side one, once leveled, is too high by 1/4".  Such is the nature of budget-minded mass-produced yachts of the 1970s.

Of course these pieces narrowed the space considerably.  I had trouble wedging my out-of-shape self forward of this to disconnect the running-light wiring (along the port side) which kept getting in the way; so I decided to cut out the bulkheads a little.

I am always wary of amorphous shapes like this (such as on the back of the Hyundai Sante Fe SUV, which is downright hideous) so I just used a 4" sanding block to scribe a line parallel to the hull and deck all round.  This picture shows the cutout with the crossmember in place.  The bulkheads are 3/8" and the crossmember is 1/2".  I use mainly good-quality cabinet-grade plywood, well-saturated in epoxy and sealed in epoxy paint (these will be done in Easypoxy).  The void to port is for the wiring, which here I have tucked back out of the way.

 

Pretty cool how the bow-locker door hinges open and fits into the curve of this new bulkhead; huh?  (Should I say I planned it this way?)

(And, yes; this is where the microwave goes.  I've written on this before.)

On most budget-minded production boats, the V-berth shelf is meant mainly to stiffen the hull above the bunktop, as this tends to be the longest and highest section of otherwise-unsupported fiberglass hull on most boats.  It's not there to be useful; and most of the time the fiddles on the shelf are so miniscule as to be only for show.  Determined to have a proper forepeak, I made these high enough (6" inside) to contain plenty of gnarly gear that will accummulate here, like fenders, mooring lines, a mooring pennant, spare tackle, and probably even a couple of sailbags (Diana's main and jib already share a bag that would fit in here as it is).  The fiddles are made of 1/4" plywood, just decent cabinet-grade lauan that I had got to finish some Barbie dollhouses for my kids.  I cut them down forward of the new bulkheads to allow the little door (the only cabinet door with hinges in the whole boat) to open fully.

 

Above is to go a mahogany plank, about 4" wide and 1/2" thick, to serve as a backing plate for the deck winch (which serves the anchor rode), the mooring cleat, and the inner-forestay attachment fitting, as well as the aesthetic purpose of representing the centerline.  Originally I made this for the full length of the space; but I will cut it and fit two pieces to the fore and aft of this crossmember.  It occurs to me to have some really nice bright white LED floodlights under the deck, forward of this, to illumine the whole compartment.

Along the deck, against the hull, kind of like a facia meant to hide the toerail bolts, I will fit a wooden cleat between the new bulkheads and the (new) chain-locker bulkheads, on which can be mounted hooks and straps on which to hang line and sailbags and other stuff.

These pics were taken a few days ago.  As of today (Saturday, 24 May) I have applied a fillet of 5200 along the hull and, using WEST epoxy, 'glassed the bulkheads and crossmember into place.  When this is kicked-off I'll be painting this with semi-gloss Easypoxy.The original faux-teak forward bulkhead will be left as original; though when I replace the door I'll be replacing the tired old brass-plated-steel offset hinges with some in SS or chrome.  My daughter Rachel hand-painted ship's wheels and anchors onto some wooden knobs for my mother's kitchen cabinets recently; there is one left over and I may use it on this door.

Stay tuned for the pics of after I install the rode-locker bulkheads and trim up here.  I've mocked it up a few times and it's going to look really cool.

* * *

It's been a long, cold, lonely winter.

The winter of 2013-2014 has been harsh to New Jersey. Most people of a certain generation are hard-pressed to recall more nasty weather. It hasn't been the frequency of snow, nor the intensity, but something like a combination of the two. We had two major power outages in the region and the township plowed exactly once in six major snowfalls. Plus I was commuting 52 miles each way to work at a marina on the Shore and lost plenty of time and income due to weather. Nearly nothing got done on Diana between early December and about five weeks ago.


Here are some updates, in no particular order.

Foredeck hatch

I finally got the foredeck hatch done (or done enough) and set it on the boat the other day, just before one of the rainfalls we've been having on and off all week.

The poor contraption has been kicking about for about three years. Here it is getting a coat of varnish after I plugged the screw holes in the two sticks on top. (They are aligned over the two ribs which stiffen the frame and the Plexiglas.) I had to take the mahogany down to about 80 grit in some places. Right now it has about three coats of Captain's Varnish on top and about five or six on the sides (on the frame).

 

Here it is (below) after I set it onto the hatch base. The construction of this is exactly as we do on the Cherubini 44-- it is essentially two boxes, a frame and a coaming, made separately. When you have fit the frame box to the deck, you slice off the top portion (in this case 2-1/4") with the table saw, rolling the thing over the blade to cut the four sides. This ensures you have a mated base and hatch. Once the base is installed on the deck, you install the coaming inside it. I set the front of the coaming back about 1/16", using some lauan doorskin plywood, to allow the bottom inside edge of the hatch to clear the coaming as it hinges open. I also slightly tapered the outside faces of the coaming, above the base, to provide clearance. Actually there is a bit more clearance than is necessary or desirable; but it's not bad.

 

As viewed in profile, the hatch base is probably too high. During my usual intellectual communing with my dad, I apologized to him for it. He would have had it a whole inch lower to the deck.

At 24 x 26 inches, this opening is sort of a forward "command center" from which one can lower or raise the anchor, navigate and deploy or stuff headsails. The dimensions also allow for the hatch cover to be unpinned from its hinges and lowered through the opening to stow it below-- a consideration I considered paramount and one which led me to increase the former molded coaming's opening (in essence I sliced out the whole molded coaming entirely).

Today I got to enjoy this in a light drizzle, which was actually pleasant. The translucent white Plexiglas allows majestic light below and even when only partially open allows adequate ventilation.

Electrical panel

I have since added the rest of the trim to this; this is a pic from a few days ago. Today I concentrated on wiring the guts of this panel. As you can see the electrical space is located along the hull shelf above the quarter berth, using the original faux-teak-plywood shelf and just adding a front and top.

 

 The small panel to the left (aft) is the 115VAC panel.  Below the double breaker is the slot for the battery-charger's breaker.

The two main 12VDC panels are for the lights and other circuits.  There is also the bilge-pump switch, voltmeter, fuel-level gauge and a 12VDC outlet.  The voltmeter reports the status of the three batteries (a two-battery house bank and one starting battery) by way of three push-button momentary switches.  There is a switch to turn on or off the fuel gauge as well (switch is not in this pic; it was installed today).

The two rotary switches forward of the double panels are selectors; one is on the running-lights circuit to choose between the masthead tricolor and the pulpit-mounted lights and the other one is on the cabin-lights circuit to choose between the white and red lamps.  In this way no one can activate a white light below when the boat is being navigated at night.  The two rotary switches are aligned with their respective master switches in the panel to their left, as though pointing towards their home circuits when they are in the "normal" positions.

Bookcase

I installed this a while ago but never got a decent pic of it. (This isn't really a decent pic either.) The bookcase is an alcove built into the head (aft end) of the starboard-side settee, under the galley counter. It is scaled for paperbacks of 6 x 9 inches and accommodates things like the Eldridge's, novels and certain tools manuals. There is a blue LED lamp inside, activated by a switch above the galley. The little plywood end (to the left in this pic) opens to a compartment outboard of the books where I can "hide" (stash) CDs and DVDs that are not immediately needed or already loaded into the computer or iPod.

 

Head compartment

Almost all the trim in the head has been installed. As built, the Hunter 25 did not come with a basin in the head; there was just an open bin above the footwell of the berth on each side. Diana's PO took out the floor of the starboard-side one and added a hanging bar so that coats on hangers draped into the footwell of the bunk. I restored a floor here and made two "duffel-bag lockers" for guests' gear. This pic shows the top of those lockers (without their access panels installed) and the trim.

 

To port I installed a proper basin for foot-pump pressure water.  The portion of the countertop aft of it lifts up to the old bin's original floor, providing a space about 4" deep for "lady products" (for my daughters) and other stuff that isn't needed every day.

The old-style black-based Whale faucet is mounted in a 7/8"-ID stainless-steel flat washer serving as a trim ring.  The other washer lying on the countertop was meant for the bottom but I haven't been able to get my (arthritic) fingers up into the access hole underneath to install it.  The aluminum tube of the faucet is a little tatty and I may opt to replace it later; so this is a job that will remain "temporary" "for now".

The lockers outboard of the sink are for towels (aft) and toiletries (forward). Right now they hold everything I took out of the galley lockers in order to finish those now.

In this picture I still owed the fiddle of the lift-up some varnish; but as of this writing it's been done.

The black conduit tubing will get tidied up. But due to the crossmember (on which the junction box for the spar wiring is mounted), the wire loom can't drop straight along the bulkhead; so it is led about an inch away along the cabin side and through a hole in the top of the locker. I did not make a fiddle here; the trim is just a common corner bead. It's too narrow a space to put anything on it anyway.

My mother, the accomplished seamstress, is making the curtains for these windows. They will span the full width of the space so that, when closed, they will be proper drapery that regularizes the oblong shape of the deadlights. The same will go for the main saloon as well.

I still have not connected the fresh-water lines to this sink. The holdup is solving the water-filter question. It's looking like I will install two undersink cannister types, one here and one in the galley. RVers tend to use a "pre-tank" filter, hooked up to the garden hose as they fill the tanks; but this requires that the water in the tanks is presumed good. Most of the bad-tasting water I've encountered has gone bad in the tanks. I'd rather apply the charcoal and coconut-shell filtration at the tap(s), so I'm looking into Purete and Whirlpool compact filters. The one I've got in mind for the head sink is meant for icemakers and its connections are for 1/4" tubing. I may be able to do without the small-ID "quick connectors" and adapt it to 3/8" supply hose for the head sink. The galley can get a 3/8" one adapted to 1/2" supply hose.

* * *

Interior developments, 2013

I have not been on this site for some time!  Here are some photos of recent progress as this boat really is coming back together.

 

Anchor-rode lockers

I have long had the idea for relocating anchor rodes farther aft in the hull.  One of the biggest detriments to performance, especially in small boats, is in carrying heavy ground tackle at the pointy end of the boat.  Of course this is where it must be deployed, and from where it must pull; but nothing but some shortsighted concept of 'convenience' says it has to be stored there.  Ancient ships brought their anchor rodes aft to the foremast or even abaft it; but this was only because the ship was sufficiently wide there to allow for a human-powered vertical capstan.  When I designed Starchase (an 84-ft lug-rigged schooner) in 1981-82, I envisioned a whole full-width compartment aft of the foremast in which sails were stowed and through which the anchor rodes were dropped to a deep well under the sole, right in front of the ballast.  This is where such weight should be; but of course it entails the leading of chain aft along the deck, which can be a tripping hazard and much else. 

 

For Diana I had already given over the idea of using the V-berth for a two-person sleeping area.  Its foot is too cramped and the whole space is too hot.  And I had already committed the after outboard corners to plumbing and such for the toilet and holding tank.  Against the forward bulkhead is the toolbox locker (with microwave above, since it's the only place a microwave can fit) to one side and a hanging locker (the only one in the boat) to the other.  So I decided to extend these lockers forward and to make room for the anchor rodes as well. 

   

My first idea was to use common plastic trash cans for the rode bins.  They're cheap (and replaceable) and, if fitted with a plain nylon through-hull, can drain into the bilge or elsewhere.  I bought two trash cans; but after cutting out the V-berth hull shelf I realized they were just not going to fit.  So I concluded the sensible plan was to use the trash cans as trash cans somewhere else and to just drop the rodes into the spaces as they were. 

 

The two bulkheads are show here, each side, before the fitting of the longitudinal bulkhead that will finish them off.  Each side will be fitted with an access plate; but the bulkheads will be removable as well. 

 

This 'glass did not kick off immediately.  I suspect bad MEKP, or just an improperly light quantity of it, as my MEKP dispenser's pickup tube snapped off in the bottle while mixing.  (This happens with MEKP dispensing bottles when they get old.  No matter what it looks like, replace it at least every three to five years.)  These surfaces will be painted in gelcoat later; but for now this is what the work looks like. 

1. Port side 

  
The white stuff is 5200, with which I seal all edges of plywood before 'glassing them to the hull.  Water intrusion along the edges of plywood where they are 'glassed to the hull is the number-one killer of plywood bulkheads-- especially where chainplates are mounted. 
 
(If you think it's sealed against water, think again.  It's a boat.  Water gets everywhere. 

2. Starboard side  

  

Here is the toolbox locker, complete with fiddles to hold the all-plastic (no metal anywhere) Rubbermaid toolbox.  Ahead is the old rode locker, above which the rode deck pipe is removed.  Though I fitted a proper drain pipe in the pointy space, to lead dribbles aft to the through-hull sump, this will be dry.  Some light comes in through the 'eye' windows, where the old hull-mounted running lights were.  (More on that later.) 

 

The battery box fitted with a PVC tube and rolls of wire is my Wire-O-Matic (shop-use wire dispenser, typically made from a box or barrel).  It even has a proper lid (the lid from the battery box)! 

  

The hull-side shelf is cut out for where the plastic trash can was; but now it broadens the space so there is less chance of the rode becoming caught under its edge when running out by deploying an anchor.  

  

  

 Main cabin (aka 'saloon')

During one of the hottest weeks of July I came out to the boat each day at 6.30 AM before leaving at 8.30 for my contract job 50 miles east.  I managed to use up a whole quart of Easypoxy on the bulkheads, which has been a great relief because it's made the boat look closer to done.  
   

  
Nearly all of the brightwork was removed before painting.  The very intricate and delicate doorjamb seemed stuck to the bulkhead with varnish and I would not risk prying it off; so I masked it.  Along the baseboard to port some residual tape can be seen.  The baseboards are actually structural-- they help hold the sole joists down against the hull. 

  

The thermometer and hydrometer are from a cheap 'weather station' I found in the trash.  I dismantled the instruments, cleaned them and painted the shells in matte black.  They work great.  Above them, on the same centers, will go the clock and barometer.  Below them is a bulkhead-mounted compass (mounted in the bulkhead! --imagine).  I consider it vital to have a decent compass visible below, with which one can check courses and at-anchor bearings.  Below below this, above the drop-leaf table, goes a clinometer.
  

The second blue plastic outlet box is for a 12VDC outlet and USB-based chargers.  The stereo goes between the empty box and the (now absent) table.
  

The four-foot-long fluorescent shop light is, of course, temporary. 

  

  

In this view the saloon is being used as a varnish shop.  The large piece on top of the workbench is the top of the 'duffel-bag lockers' outboard of the toilet in the head.  The other plywood piece is the top of the galley bins.  The rest are just various bits of mahogany that go all over this compartment and in the head. 

  

Plugs have been added to the vertical grab posts (at last!).  Typically I varnish the main piece a few times before adding plugs so that the plugs receive a few coats less and so show as a lighter color.  This is just an aesthetic I happen to prefer; and I have always done it this way.  

  

The galley counter is still covered in cardboard.  I have decided to add ceramic tiles to that 3-inch-high bulkhead above the settee. 

  

The small red toolbox is the 'jewelry box', in which I keep all the cool rigging stuff (my favorite parts). 

  

Here too can be seen the side of the speaker box, at the forward edge of the hull shelf, and where I 'glassed the small athwartships bulkhead of it to the hull.  The white-pine stick, old iron C-clamp, and red-handled squeeze clamp (almost hidden from view) are currently holding this shelf up into position.  Like the ones in the V-berth these two did not match each other, sideto side; and this one sagged while the one to port tilted up.  The stick is forcing it up till the 'glass cures.  Hopefully this will remedy some of the problem; but the little mahogany block under the forward end of the shelf (partially painted white, because its proper replacement is undergoing varnishing) will assist in this.

  

Other stuff

Here is a pic I took, on my back, up at the new foredeck hatch with the old hatch, which fit only the original trapezoidal molded-fiberglass opening, on top.  Still waiting on white Sikaflex 295-UV to complete the new one.
  

The terminal blocks are junctions for the spar wiring.  These get screwed to the teak crossmember (now painted white) and enclosed in a cute little mahogany box with sliding door, currently undergoing varnishing.  

   

   
At the other end of the boat, I 'glassed a short bulkhead across the back end of the fuel-tank shelf, tucking it in just ahead of the fiberglass rudder-post tube.  The problem with all skegless rudders is that they are liable to catch something nasty, such as when shooting some dodgy inlet.  In this eventuality, there are two possible outcomes: one, the rudder will break off below the stainless-steel shaft (preferable) or, two, the rudder, tube and all will tear backwards and out of the boat (not good).  If this were to happen, there is little anyone could do to save the boat-- unless that water were able to be confined to a watertight compartment.  ALL rudder tubes should be isolated from the rest of the boat, so that intruding water cannot invade the rest of the hull and overwhelm the bilge pumps.  (We all did learn something from the Titanic; right?)  
  

 

This bulkhead is not high; and it will be fitted with a drain tube as well-- but in the event of a leak at a stricken rudder tube, the drain can be plugged and this compartment will contain much of the water before it is overwhelmed.  This may be enough time to shift weight forward, get something over or into the torn hole(s), or fix or reroute a pump to handle the inundation.  In any case it's far better a solution than that on most other boats-- which is to say it's better than nothing at all. 

 

The little block is just holding the bulkhead in place and gets removed.  In fact I painted this recently and probably should have taken a newer photo.

 

The little step in the foreground was added for climbing down into this locker through the cockpit-seat hatch, which I have done about 350 times since I have owned this boat.  I got tired of leaning over and lying upon the edge of a 3/8" piece of plywood.  Above this is the top of the under-cockpit locker, forward of the fuel tank, which is accessible through the quarter berth and, as of this writing, is now isolated from the rest of the under-cockpit space and its attendant gasoline fumes. 

  

 
* * *

Cockpit-seat lockers

These are some older photos that never got posted under any specific topic.  In most cases there has been much progress since these were taken.

1. Here is a view into the port side locker, what used to be the fuel-tank locker.  As I have said before, this area was so soggy when I acquired the boat that I removed the bulkhead and shelf with bare hands-- really; no tools needed!  The bulkhead was formerly under the drip rail to the right.  I made a new bulkhead about 8 inches farther aft, to make the quarter berth about 6'4" or 6'5"; the foot of it is under this shelf, which, with a fiddle installed, will hold winch handles and the like.

In this photo the shelf is holding a plastic bulkhead vent fitting which I may end up not using and a length of SS angle intended for the backstay's backing plates (since substituted with aluminum).

Outboard is a little box/shelf I made to hold quart cans of paint, solvent, 2-stroke oil, and whatever.  It drains into the area farther inboard.

I really hate black 5200-- it always looks unclean and messy somehow.  But it's what I had; and this will all be painted in white Bilgekote.

The port-side battery's breather tube comes up through the box/shelf and extends up like a snorkel to within a few inches of the underside of the coaming (the PVC coupling seen on the shelf is for that).  The battery is under the main-cabin settee.

The after bulkhead replaces the one that was there holding up the fuel-tank shelf.  The 3" hole will accommodate a ventilation tube leading from the Dorade box (after of the tiller head) to the foot of the quarter berth.  This will be PVC, as it should be rigid to keep from being damaged when stuff gets dropped or thrown into this locker.

You can see the bodged-up job the PO did in increasing the size of the openings in the hatch's drip rail.  The real reason he had such leaks is because he had cut out the drip rail itself along the outboard side of the hatch to accommodate overly-big hinge bolts.  I patched this, not prettily, but adequately to lend it strength.  This will get sanded and reshaped prior to paint.


2. This is a look straight down at the starboard-side locker.  At one time the fresh-water tank was under a platform at the forward end of this space.  It was not there when I acquired the boat.  My new fresh-water tanks go under the main-cabin settees.  I fitted this shelf in here to lend stiffness to the hull the way the quarter berth does on the other side.  All major flats and verticals should be structurally bonded to the hull-- they all help.

For access under this shelf I made two lift-out panels.  I really cannot think of what I would put down there, as the top of this shelf will be full of things like life jackets, mooring line, fenders and a folding bike.  The inboard opening without a cover (left side of the pic) is for the engine-starting battery.  A standard-sized battery box fits into here with its ear handles holding it from sinking all the way through.  Of course this will get screwed in place-- and a strap fitted over the cover when the battery is installed-- as well.

The little block of mahogany is a step I made on top of the edge of the stiffening rib so that, for the many times I have climbed down this hole for access under the cockpit and aft, there is something to step and lean upon that is more substantial than the knife-edge of a piece of 3/8" plywood.  (My back is grateful for this!)

Under the cockpit at the lower edge of the photo you see the black plastic (Tempo) fuel tank, which is 11.5 or 12 gallons.  It sits on a plywood shelf, the edge of which protrudes a bit this side.  As it is located, the tank is about one inch off center but otherwise fits perfectly, with all access points at the after end for vent, sender, feed and fill.

The openings in this hatch's drip rail were enlarged too but not as clumsily as the ones on the port side; I filled and faired these as well.

3. This is a look from inside the starboard-side locker, looking forward.  You see the two lift-outs and the hole for the battery box.  All of this has received one coat of Interlux Bilgekote; it'll get another coat before it's done.

The things in the forward corner are a brass tube, which will be installed in that bulkhead, down by the hull, to admit bilge water from this compartment to where the bilge pump is, and the ends of the PVC tubes that lead to the electric and manual bilge-pump pickups.  I made this section of them in PVC because it would be nightmarish to thread any replacement hose through this route once the boat is done.  PVC can be assembled in pieces, in place, so even in the unlikely event that the PVC might fail it too can be replaced after being hacksawed out.  From this point hose, with check valves to avoid backfill, will lead towards the transom outlets.  The vertical PVC tube mounted on the plywood block is the starboard-side battery's breather which extends up to within a few inches of the underside of the deck.  The battery is located under the settee berth.

The wooden bulkhead is the back side of the teak plywood bonded to the inside of the cabin back.  It extends down below the galley counter back here and provides a surface to which to fasten wiring and other stuff.  In this plywood will be fitted the on-off switch for the engine-starting battery, so one can reach down to the galley from the main hatch and switch it on or off.  Also the wine lockers will be mounted in this bulkhead (more on that later).

The long skinny shelf along the side of the cockpit (to left in the photo) will get a varnished-mahogany fiddle to hold stuff (mainly because I have plenty of countertop-fiddle stock).  This shelf was installed to seal the under-cockpit locker from potential fuel fumes (the tank is out of view just to the left of the camera).  This whole compartment gets vented via a Rule #140 blower and a hose leading to the Dorade box.

Just forward of the drip rail (angled feature at top left in photo) in the cockpit side will be mounted the throttle and shift for the motor; so those cables will run straight towards where I was holding the camera here.  Also the Whale manual bilge pump gets mounted in the cockpit side just to the left of the camera.


* * *

Surprise, surprise

Here on poor Diana the V-berth area has been the last part of the interior to get any attention at all.  One of the first things I did was to install the holding tank under the after end of the bunk; but since then it's been partially dismantled and not much has been done here.  (Stay tuned for a forthcoming post on this compartment when the through-hulls go in.)  The V-berth area has been used as a lumber bay for too long.  The other day I cleared it all out and stashed the usable lumber (mahogany, spruce and white pine) in the house's attic.  By the time I had swept and vacuumed out the V-berth area I felt like I had got a huge load off my conscience.  Suddenly there is actual space in this boat!

And the boat must have lost 200 lbs as well!

Here is a (lousy) photo of the V-berth right after I swept and vacuumed (for the first time in I won't say how long!).  The 5-gallon pail full of wood bits (mostly Honduras mahogany) is the only remainder of the once daunting heap that formerly occupied this space.













While laying out the forepeak lockers (more on this later too) I observed that the 3/8"-plywood bunktop felt distressingly flimsy.  Just kneeling on it was enough to bend it far too much out of level for my liking.  I have already done all the other bunktops, removing the old cleats for the lift-out panels, installing new ones saturated and bonded with epoxy and peppering each one with plenty of #8 screws.  Each time the bunktop has become stronger and stiffer.  If these bunktops are 'glassed to the hull-- and they are-- they should be structural members in their own right-- and so they are, now.

Hunter used plain white-pine 1x2s for lift-out cleats, the same as you buy at Lowe's or Home Depot.  Some of them had edges that had been smoothly routered to about a 1/4" radius, in order to protect your knuckles when you are rummaging about in the compartment.  But even if they were glued to the plywood with wood glue (and some of them, like the V-berth ones, were not) they were merely painted with Pettit Fiberglass Undercoater and otherwise left alone.  In the middle compartment under the V-berth, three of the cleats were sound enough that they did not require replacement (at least, not today).  The cleat along the aft edge was both too loose and too short to lend much stiffness of the bunktop.  So I removed it and fashioned another one out of a piece of 1x3, essentially the full width of the bunk at that point (about 34").  Properly fastened (with screws and then cured epoxy) it will stiffen the whole structure.

Inside this compartment was a straggling bit of old electrical wiring, leading through the bilge to the rode locker for the port and starboard running lights in the hull.  All right; first, I never run wiring through the bilge.  All my new wiring is run under the hull-to-deck flange.  There it's accessible and out of the muck.  Second, this wiring is red and black, and also 16-gauge, neither of which is code for boats any more; so I have run all new red-and-yellow 14-gauge and so this wire is redundant.  And, third, I am not reusing the port and starboard running lights in the hull.  They are too small and too low to be of much use except when motoring through a calm harbor at night.  Diana will get a one-light red-and-green unit, with an LED bulb, mounted on the pulpit.

I tugged and tugged on the wire and realized I could not pull it out.  Sure enough, the wire disappeared through the middle compartment's forward bulkhead, passed through the dead-air space and emerged at the bottom of the rode locker.  Obviously the entire interior structure was assembled outside the boat-- and all the wiring stapled to where it should be-- and then installed in the hull in as close to a completed state as possible.  This is how Hunter built five of these boats each week.

Now I despise all dead-air spaces on boats.  If it's inaccessible to humans, rest assured it won't be to humidity, bugs and bilge water.  Who knows what might be going on inside there?  And an application of Murphy's Law ensures that if you have a problem leak, or hidden rot, or a bug infestation, it's going to be in the one compartment into which you cannot readily get.  I had already resolved to open this compartment, at first by installing an 8" clean-out plate and then, in interests of simplicity and economy, just cutting a lift-out hatch into it and adding fiddles.  Also it would give me the chance to inspect it and to apply some epoxy to what I was sure was bare plywood in there.

Following this philosophy I have already cut access holes into the feet of the settee berths which extend through the main bulkhead.  Formerly these spaces were inaccessible and yet open for leading wiring and attracting humidity and bugs.  Now the one to port is convenient for installing and maintaining the Whale footpump for the head sink.  Both these new-found compartments are done now-- but one lacks a lift-out panel as I just do not have any scrap 3/8" plywood, since I don't like to use it for much of anything.  I do have some specific need for a sheet of it soon (more on that later) and will remake a lot of the old lift-outs till it's all gone.

I laid out an opening of about 9 inches square and rocked the jigsaw in to avoid drilling 3/8" starter holes and to save the cutout to use as the lift-out panel.  A can of Krylon supplied the corners' radius.  The piece of plywood came out perfectly-- and then, for the first time in 37-1/2 years, a human being gazed in at the compartment beyond.  And-- what a surprise.

This photo shows the space after I sanded some of the fatigued paint and got ready to install the new cleats.  At the forward end is the new hatch, about 9 inches square.  It might serve as a secondary rode locker if my idea of the plastic trash cans doesn't happen.  This is one storage space Diana now has that most H25 owners don't even know about!  The bare wood at an angle in the center compartment is the new white-pine cleat that just happens to be lying in the space (had to check if it was not too wide for it).
Having seen the top photo you will notice I started peeling off the old hull liner.  This chore is not particularly hazardous but really makes a mess.  I have invented a vacuum attachment that has a 6" putty trowel and a tube for a handle that plugs into the vacuum hose, expressly for doing chipping work (what we at CBC called 'pachippulating') like this.  I'll try it out here (rest of hull liner is already off).  Really the hull liner up here is not in such bad shape and you can see it's had good adhesion.  But it's dry and a little crispy and Lord knows how clean it is.  I am replacing it with the 'Irish tweed' stuff from Defender.

What I found in this cubbyhole was remarkable.  I had been particularly distressed because the accumulated junk, that had been condemned to remain in the middle compartment till I cleared out the lumber, included a two-foot length of rope that was sopping wet.  From where did the water come?  The rest of the compartment appeared dry.  The bits of scrap wood in there with the rope were damp but nowhere near as wet as the rope.  The hawsepipe on the deck is taped over against weather.  All I can account for is that the holes from the stem fitting that was removed (see them in the top photo) are still open, though on a negative angle, and rain and snow must have been blowing in there all autumn and winter and running down through the rode locker and the dead-air space to the second compartment (though I never noticed water in the holding-tank one beyond, to which all of the forward ones drain).

But, no worries.  The dark-green glass of the inside of the hull, at the very end of the bilge, appears sound, strong and-- most surprisingly-- dry.  Even more surprising, so does the plywood.  It is not damp or dark or even smelly.  For some unfathomable reason the untreated wood, which should have been a totally gooky mess in a compartment that admits drainage water but no air, has remained bone-dry and free of rot and mildew for over three and a half decades.

This 'first look' at the newly excavated space shows perfectly healthy dark-green fiberglass resin, a tight layup, no evidence of water intrusion or delamination and, best of all, no damp or rotting plywood-- even though the plywood surfaces were all unfinished (and I mean RAW plywood-- no paint, resin or-- had Providence intervened-- epoxy (which maybe no one but my dad had heard of in 1974).

The little black circles on the bunktop are my marks for the screw holes.  There seem like so many! --but keep in mind four pieces of wood have to be installed here.

The grey stuff along the one side looks like oozed-out deck putty.  I do not think (nor hope) it's a mud-dauber nest!  But really there could have been anyone living in here; and there is no one.

The stick lying at the forward end is an old cleat being reused as the new forward cleat, yet to be installed in this photo.  I always make cleats as long or wide as possible to add stiffness across the crosswise grain of the merely-3/8"-thick plywood.  Properly adhered, a new cleat does wonders.

I reused another removed cleat for the after one of this hole.  Being 1x2 stock (1-1/2" wide) it goes smack up against the forward face of the after bulkhead of this compartment (at the bottom of the photo).  I planned it like this when I laid out the opening.  This way the after edge of that cleat is adhered with epoxy to the face of the bulkhead itself.  In many cases the tops of such bulkheads are where moisture intrudes to generate rot, since the bottom edges, along the hull, are typically better treated when the boat is assembled.  I really do not relish the thought of replacing an under-bunk bulkhead, especially when it's so easy to avoid ever having to do it.

The bits of plywood to the sides are a piece of scrap that I found in the 5-gallon pail of blocks and cut to fit (notice the one under the flash came from the end of the other).  I don't care about their shape-- you only see the parallel edges in the access opening and these bits of plywood have been, as of this writing, thoroughly saturated in epoxy and well-adhered to the underside of the plywood, which I also saturated before installing the fiddles.  As soon as I drill a 3/4" finger hole in the cut-out panel it will be painted in epoxy too and replaced as the new lift-out panel.

I will post photos of how these silly cleats and all have gone together after the epoxy dries.  This whole space, including the underside of the plywood, will be painted in epoxy later and then in white Interlux Bilgekote as soon as it's warm enough to ventilate the space and enable paint to dry.  The bunktop will get done in Durawhite (or whatever the new water-based mildew-resistant paint Pettit is offering now that replaces it).
 
I have not yet decided if it's worth it to extend PVC drain tubes from each of the forward compartments into the after one (where the holding tank and through-hulls are) in order to isolate them from each other.  Any of these might make a very good stash hole for bottled water, blankets, sweaters, boots, and various gear; and as with the one under the cockpit it would be really nice to keep a mishap in one (or water from the hawse pipe) from wetting them all.  Plugs in the ends of the drain tubes would keep them dry till you needed to evacuate them.

An argument-ender and a joyous surprise

Here is another funny bit which I hope will support some of the points I have so often attempted to make about the lack of absolutism when it comes to maintaining quality in a boatbuilding enterprise.

Many times a prudent selection of materials or methods can facilitate significant savings to both the builder and customer without sacrificing utility or durability in the product itself.  Intelligent boatbuilders and designers know where 'good enough' is good enough; and I submit that no engineer in a non-boating field, and certainly no wannabe, should stand on ceremony as to ideal technical specifications when the boatbuilder and designer far outrank them in terms of knowledge base, expertise and focused training and experience.

And so, to the positive example.  How many have claimed that marine plywood is the sole material in use on production sailboats?  I have rebuilt the whole interior of Diana without using a single bit of it; in fact my material of choice is lauan cabinetry plywood, well saturated in WEST epoxy and properly finished in paint or sealer and varnish.  None of this is inadequate when properly done .

Having just cut open the forward end of the vee berth to give access to the forwardmost compartment under the bunktop (in another post here), I took the cut-out piece to the bench to sand its edges in order to use it for the lift-out panel.    Turning over the 9-inch square of plywood I made a startling discovery.

(And how on earth did I happen to choose the exact right place to cut out so that I could have this message appear on the back of the panel?)

If you cannot read it in this photo, here is what it says:

'Roseburg' [name of plywood mill]

'Resin Tite' [trade name]

'Hot pressed' [lamination process]

'Exterior glue'

Hah! --the bunktop in this 1974 Hunter 25 is AB-grade exterior fir plywood-- not marine plywood.  This raw-- unpainted, untreated, unfinished-- piece of plywood has survived 37-1/2 years, much of them seeing little maintenance or attention, in a cheap production sailboat used almost exclusively in a saltwater environment on the New Jersey shore.  This very piece came from a closed-in, dead-air compartment with no ventilation which no one has laid eyes or hands on in all that time.  And it shows NO signs of rot, water saturation, mildew, dampness, discoloration or anything.  It's as healthy as would be a piece of plywood stored in your attic.  Simply amazing.

Just so you know.  :)