Finalizing cabin and interior

Here are some pics of recent progress belowdeck.  Currently (June 20th) I am finishing the cabintop, fitting the Dorade boxes and hatch shroud, and remedying the PO's repair of the bow in preparation to paint the hull and fit the stem fitting.

Hanging locker

Aft of the port-side rode locker, opposite of the microwave and toolbox, was planned this locker.  In framing it I realized there was much more space than I expected.  As it is now, it has several bins to hold shoes, balled-up t-shirts and cottons, various personal effects as well as 12" worth of clothes on hangers.  Shirts and coats will fold onto the floor; but it's much better than having nowhere to hang clean clothes at all.

The first photo shows the after bulkhead, where the plumbing is (which necessitated the locker being delineated from the bunk space in the first instance).  The 1-1/2" vented loop is for the holding-tank pumpout; the smaller standpipe is the holding-tank vent which goes to a 3/4" through-hull in the hull.  The wiring will go to a 3-gang panel over the head sink for the lights.  The little 1-1/4" elbow shown coming through the wall is the head-sink drain, going to its trap and thence to 3/4" hose for the seacock.

I don't know if I've said this before but, when fitting plumbing traps to boat sinks, one should always make them turn forward or aft first and then inboard only after they have gone downwards, to ensure sufficient drainage on either tack.  (This says nothing about the shape of the basin which may retain water to leeward of the drain; but that can't be helped unless you have a basin more steeply sloped than the usual angle of heel.)

The other pic shows the forward side of the same locker.  The "Get A Grip' placard came from a hook-and-loop strap display at the West Marine store where I worked; I thought it was hysterical and swiped it from the trash when the sale was over and cut it to a minimal size (and then spilled acetone on it, causing the blur).  It's been in the boat for about 6 years and by now deserves a place as decor.

 

This locker will get covered with a canvas curtain to keep water out, as the foredeck hatch is directly overhead.

The vertical door-jamb pieces probably need some cleaner way of terminating outboard of the sill-- I'll look to that later.

Main cabin, aft

These two pics show the back corners of the main cabin, the electrical panel to port and the galley and bookcase to starboard.  Among other things can be seen my re-use of the (1974) teak fiddle rails that were originally fitted to the outboard hull shelves over the settees.  This wasn't an easy task since the cabin, as molded, is not symmetrical-- the port-side bulkhead was fully one inch wider than the starboard side, as is evident since the vertical posts are keyed to the hatch's opening.  The solution lay in justifiying the space between two spindles on the center of the opening and then ensuring that no spindles are too close to the ends.  I think one of them is a little off, by less than 1/8", but you won't be able to tell (and one strict rule of Diana is that no one is permitted to visit this boat with a ruler in hand!).

In the spirit of complete disclosure: the cheek piece at the after end of the overhead cabinet (where the radio goes) is teak, not mahogany!  It came from a very weathered piece in a trash bin and I didn't recognize it till I'd sanded it down and applied varnish.  Oh, well-- at least both sides are the same (from the same board in fact).

On neither side is the cap fitted to the top of the divider bulkhead.  I've been getting impatient about getting this stuff varnished and installed, just so it doesn't clutter up the cabin and inhibit other progress (as it's all been doing for too many years) and so I screwed this stuff into place as it is now.  I'll fit the cap pieces after I finish the after side of these bulkheads (more on that-- and a surprise! --later).

I haven't had the motivation to build the drawers for the galley yet and so the cabinet bulkhead beside the ladder is still missing.

I don't go in for the trite little piracy fetish so many yachties favor; but the skull-and-crossed-bones can cooler is in tribute to my late cousin Peter, who co-founded Raider Yacht (for which this was a logo).  So it shall remain on the boat.

  

Other stuff

Here is a cool pic of the foredeck hatch.  It lets in some phenomenal light-- you can read by it in the saloon, even during a rain, even with the other hatch closed.  I've been saying all along that if this project is taking far too long, at least I get to spend my days with gorgeous bits of varnished Honduras mahogany; and here's an example.

The stick holds up the hatch because the hardware isn't on yet.  The cords are what secures it down against wind, rattles and motion.

The green tape is a sign reminding me which end goes forward.  Remember that the hatch frame is cut from the base on the deck, to ensure that they fit together, before the base is installed.  Even with a rectangle it matters which way it goes.

Below is a pic of the (too dusty!) sink in the head.  The cabinet lift-out panels are not painted and so not fitted yet.  The leaning board is the divider, not screwed in, that will hold a shelf in the forward locker.

The portion of counter after of the seam in the fiddle hinges up for access to a 4-inch-deep bin (the original bin over the footwell of the settee berth.  The astute will recall that this idea was my contribution to this boat's design in 1972; see here).

I messed up the trim stick that goes atop the blue countertop along the forward bulkhead and it hasn't been remade and installed yet.  In (typical) impatience I had just "eyeballed" the angle against the fiddle and cut it; and it's too wrong to be tolerable.

I could have tugged the wire loom a little more tightly into the upper shelf, under the window, for this pic; but there's still wiring to be run in it.

Don't say anything about the after cheek piece protruding below the upper fiddle rail while the forward one remains even.  This is an oversight and will be remedied!  The trick deserving the credit is in the making of both cheek pieces, one wide and one narrower, so that they align with the locker face which, which like the sink-counter face, is parallel to the centerline.  How else would it have been done?

And this allows the curtain rods to be fastened to the cheek pieces, more or less parallel horizontally.  My mom, the accomplished seamstress, is currently making the curtains for these hull windows.

Main saloon

Lastly here is a pic of the saloon bulkhead after I fitted the cheek pieces along the top.  This had been long unfinished because I just didn't know a way of making it all in one piece; and then (in the shower, as so often happens) I conceived of the positively brilliant notion of making each side in two pieces.  I wanted some straight line to avoid emphasizing the roundness of the cabintop in here; and here is my solution: an ogee curve descending to a second cheek piece and a further horizontal line.  Together these just about cover the ragged fiberglass tape (though not quite) and represent an apparently-structural deck beam in conjunction with the compression post (the true structural deck beam is on the forward side of the bulkhead, requiring the horizontal door header).

In keeping with the conceit of having these pieces represent a real deck beam, I deliberately made these of Phillipine (lauan), not Honduras; so they appear greyer, darker, a little greener than the footwell trim and table cleat mounted lower on the bulkhead.  The cheek pieces to cover the gap between bulkhead and cabinside will be of (thinner) Honduras.

All of these pieces, as well as those on the forward side of this bulkhead, are "permanently" installed now.  If the white or varnish requires any more touching-up, it'll be done with them in situ.

I should have reinstalled the arched door header here; but in fitting the cheek pieces I ran one screw into the bulkhead, thinking it would be covered by the door header, and just missed; so I have to fill it and paint it again first.

Dave saw this and commented on my practice of simply screwing these pieces into place without concern for hiding the screw heads behind plugs or multiple cleats, saying it was just like what Uncle Joe would have done.  I took that as a high compliment, as I have long admired Uncle Joe's clearheaded sense about what's least complicated being the most aesthetically pleasant... but I really meant it all this way to be able to remove all these pieces for varnishing (and revarnishing.  As I always say, 'It's never the last coat of varnish!').

I have a really cool idea for after I paint the fiberglass around the companionway hatch (where the centerline is indicated, top of photo); but I won't share that till it's been done.  Stay tuned.

* * *

Waterline stripe

I've been getting frustrated that the progress I have been making on this boat does not look like progress; so I reached a limit recently and opened the can of Pettit Protect I've had for over a year and just went for it.  I cannot say this is a perfect job; there are minor spots in the hull I really should have faired better or filled better, and of course the first roller cover broke down after two coats and for the third I had to dig into my horde of stores for another which was too nappy and not as good.  But the paint's on the boat and that's good enough. 
   
I chose the Pettit Protect over Interlux Interprotect for one solid reason.  To reach the desired thickness, Interprotect requires five coats where as Pettit Protect requires only three.  It goes on thicker.  Therefore I accomplished this with only one roller replacement and in only about three hours of a hot Saturday in August.  
   
The rugged outline of the top edge of paint wants explanation.  In filling and fairing the hull's numerous cracks, I encountered quite a few of what I determined were 'bottom-style' cracks above the designed waterline, especially in the bow.  These are typical of any boat; and for a sailboat that one must conclude will be heeling more often than not, under way, the imposed delineation of a waterline is pretty arbitrary.  So I prepared these places as I would for any 'underwater' area; and once the waterline is established the gray can be sanded down above the line to accept topsides paint.   
  

The black Sharpie lines, applied at the upper edge of the green-tape stripe, will represent the lower edge of the painted stripe(s).  Thus I am 'cheating' the original waterline up about two inches.  

I lowered the rudder in its shaft tube but without digging a hole I was unable to remove it entirely.  As of this picture it has been sealed and re-'glassed (the yellowish stuff is epoxy, with some Microlight filler).  I found every seam in the rudder shell to have been open and filled with bottom paint (not a good sign), which was responsible for the whole thing being saturated in water.  As I used up all the Pettit Protect on the hull, I will have to buy more for the rudder and the stand squares.
   
From earlier photos one can see that I stripped the entire hull bare-- leaving no stripes.  Earlier I had plotted all three lines-- float waterline, designed waterline, and top of bootstripe-- and recorded the measurements.  These current lines come from those plots.
   

 

This sort-of-closeup view shows my 25-foot Stanley tape clamped along the toerail of the boat.  Using this as a kind of number line, I dangled the other Stanley tape from this, at prescribed intervals, taking 'soundings' down along the hull to the stripe.  To get the waterline back onto the hull, I had only to read my numbers back and to plot the marks from them.  
  
I am not sure I'm happy with the replotted marks.  Though I did the plotting accurately, I fear the boat is going to be too heavy, especially forward, and especially to starboard, which worries me.  To starboard are the engine-starting battery, the galley, the toilet itself, the toolbox, the primary anchor and (short) chain rode, and the microwave oven as well as the skipper's usual sitting area below, where the computer and stereo are located.  Everything else is more of less balanced out by a complement to the other side.  For now I shall let these lines alone and count on shifting some weight about (possibly by storing all canned goods to port, for example).   
   
In the background Jerry's 1980 C44 can be seen.  Jerry's a liveaboard who's been doing a heroic job stripping bad 'glass from his boat's bottom and re-'glassing the whole thing.  His stamina and indefatigable fortitude are an inspiration.
  

  
After taking some of these pics I just had to snap this view of Diana's underside all recently done in pewter gray undercoater (Pettit Protect).  
  
Yes; the keel looks a little bent out of shape.  Believe me-- it was much worse before I got my hands on it.
   
The paint does look a little blotchy in this view.  Maybe it's glare.  I can vouch for the effort than went into smoothing this; and the result really is pretty good.  Undoubtedly it's better than it was when new.  
  
The little oval block affixed to the bottom, aft of the keel, is the fairing block I made for the bronze drain plug.  Maybe it's just overkill; but, then again, every girl can use a little help....  
 
  

* * * 

Custom cooler

This is my really cool customized camping cooler for Diana.

Here shown holding what it usually does-- iced tea-- is the interior of the cooler as I modified it.  The divider is Plexiglass left over from the cabin windows.  It slides down into place between Starboard fiddles mounted in 5200 (to seal the screw holes so water doesn't get into the foam core; it does not stick to Starboard).  The side corners are cut out to let water reach the drain fitting, a plastic one I installed in the forward end.  The drain deposits its dribble into a PVC receptacle in the floor of this compartment which in turn carries the dribble forward into the bilge.  The drain in the cooler is cut off flush with the bottom so the cooler will sit level (and thus structurally sound) on a flat surface like the dock.

Beyond the divider Starboard fiddles hold a grilled shelf for smaller items.  The bagged ice goes under the grill.  (This cooler is not big or strong enough to hold a full block.  Nevertheless, with a plug in the drain it will hold some residue of ice-- not merely cold water-- for 5 days.)  With this configuration, there is a place that remains free of ice cubes to hold taller things, like full gallons of water or iced tea, wine bottles, etc.  The smaller stuff goes above the ice in back.

The grill is a leftover section from the light baffle material I got when installing a work light in my mother's kitchen.  It is not very strong and was annoying to cut, as a jigsaw only shattered it and a bandsaw did only a little less damage.  I resorted to cutting it by hand with a very fine hacksaw blade.  Of course the sides are not parallel, due to the cooler's shape, and the back edge is slightly rounded.  And then there is the issue of ensuring that the square holes, when cut through, allow enough support along the fiddles.  As can be seen I got it aligned so that one long strake rides on each side fiddle.

The cooler is not a 'marine'-spec one but a standard Coleman '5-day' campers'-spec one.  The marine ones all have top hinges along the side.  As seen here Diana needs one hinged from the end-- or, as here, not at all.

The cooler sits under the ladder; its top is covered by the bottom step (which I personally never use, as I step on the quarter berth edge when entering or leaving the cockpit).  This step is hinged at the back.  I do not yet have it rigged but I want to have a Fastpin slid through the ladder side(s) to hold up the step.  Then one can lift the cooler lid without having to hold up the weight of the step.  The step does not protrude far enough beyond the upper one to allow anyone to accidentally step on it and break it or bend the Fastpin.  If it's pinned up, you will see there is no step below (or just the cooler lid) and step onto the quarter berth instead.

The pencil scribble on the not-yet-painted right side (left in photo) is marking where the recessed red LED footlight will go.  With the step and lid down, it illuminates the step.  With the step up, it illuminates the cooler.

The heavy fiddles screwed to the sides support the step, which is 1/2" plywood with a 3/4" step plate epoxied to the front edge.  It was varnished about 7 years ago with Captain's Varnish and is still holding up well.

* * *

Cockpit-seat lockers

These are some older photos that never got posted under any specific topic.  In most cases there has been much progress since these were taken.

1. Here is a view into the port side locker, what used to be the fuel-tank locker.  As I have said before, this area was so soggy when I acquired the boat that I removed the bulkhead and shelf with bare hands-- really; no tools needed!  The bulkhead was formerly under the drip rail to the right.  I made a new bulkhead about 8 inches farther aft, to make the quarter berth about 6'4" or 6'5"; the foot of it is under this shelf, which, with a fiddle installed, will hold winch handles and the like.

In this photo the shelf is holding a plastic bulkhead vent fitting which I may end up not using and a length of SS angle intended for the backstay's backing plates (since substituted with aluminum).

Outboard is a little box/shelf I made to hold quart cans of paint, solvent, 2-stroke oil, and whatever.  It drains into the area farther inboard.

I really hate black 5200-- it always looks unclean and messy somehow.  But it's what I had; and this will all be painted in white Bilgekote.

The port-side battery's breather tube comes up through the box/shelf and extends up like a snorkel to within a few inches of the underside of the coaming (the PVC coupling seen on the shelf is for that).  The battery is under the main-cabin settee.

The after bulkhead replaces the one that was there holding up the fuel-tank shelf.  The 3" hole will accommodate a ventilation tube leading from the Dorade box (after of the tiller head) to the foot of the quarter berth.  This will be PVC, as it should be rigid to keep from being damaged when stuff gets dropped or thrown into this locker.

You can see the bodged-up job the PO did in increasing the size of the openings in the hatch's drip rail.  The real reason he had such leaks is because he had cut out the drip rail itself along the outboard side of the hatch to accommodate overly-big hinge bolts.  I patched this, not prettily, but adequately to lend it strength.  This will get sanded and reshaped prior to paint.


2. This is a look straight down at the starboard-side locker.  At one time the fresh-water tank was under a platform at the forward end of this space.  It was not there when I acquired the boat.  My new fresh-water tanks go under the main-cabin settees.  I fitted this shelf in here to lend stiffness to the hull the way the quarter berth does on the other side.  All major flats and verticals should be structurally bonded to the hull-- they all help.

For access under this shelf I made two lift-out panels.  I really cannot think of what I would put down there, as the top of this shelf will be full of things like life jackets, mooring line, fenders and a folding bike.  The inboard opening without a cover (left side of the pic) is for the engine-starting battery.  A standard-sized battery box fits into here with its ear handles holding it from sinking all the way through.  Of course this will get screwed in place-- and a strap fitted over the cover when the battery is installed-- as well.

The little block of mahogany is a step I made on top of the edge of the stiffening rib so that, for the many times I have climbed down this hole for access under the cockpit and aft, there is something to step and lean upon that is more substantial than the knife-edge of a piece of 3/8" plywood.  (My back is grateful for this!)

Under the cockpit at the lower edge of the photo you see the black plastic (Tempo) fuel tank, which is 11.5 or 12 gallons.  It sits on a plywood shelf, the edge of which protrudes a bit this side.  As it is located, the tank is about one inch off center but otherwise fits perfectly, with all access points at the after end for vent, sender, feed and fill.

The openings in this hatch's drip rail were enlarged too but not as clumsily as the ones on the port side; I filled and faired these as well.

3. This is a look from inside the starboard-side locker, looking forward.  You see the two lift-outs and the hole for the battery box.  All of this has received one coat of Interlux Bilgekote; it'll get another coat before it's done.

The things in the forward corner are a brass tube, which will be installed in that bulkhead, down by the hull, to admit bilge water from this compartment to where the bilge pump is, and the ends of the PVC tubes that lead to the electric and manual bilge-pump pickups.  I made this section of them in PVC because it would be nightmarish to thread any replacement hose through this route once the boat is done.  PVC can be assembled in pieces, in place, so even in the unlikely event that the PVC might fail it too can be replaced after being hacksawed out.  From this point hose, with check valves to avoid backfill, will lead towards the transom outlets.  The vertical PVC tube mounted on the plywood block is the starboard-side battery's breather which extends up to within a few inches of the underside of the deck.  The battery is located under the settee berth.

The wooden bulkhead is the back side of the teak plywood bonded to the inside of the cabin back.  It extends down below the galley counter back here and provides a surface to which to fasten wiring and other stuff.  In this plywood will be fitted the on-off switch for the engine-starting battery, so one can reach down to the galley from the main hatch and switch it on or off.  Also the wine lockers will be mounted in this bulkhead (more on that later).

The long skinny shelf along the side of the cockpit (to left in the photo) will get a varnished-mahogany fiddle to hold stuff (mainly because I have plenty of countertop-fiddle stock).  This shelf was installed to seal the under-cockpit locker from potential fuel fumes (the tank is out of view just to the left of the camera).  This whole compartment gets vented via a Rule #140 blower and a hose leading to the Dorade box.

Just forward of the drip rail (angled feature at top left in photo) in the cockpit side will be mounted the throttle and shift for the motor; so those cables will run straight towards where I was holding the camera here.  Also the Whale manual bilge pump gets mounted in the cockpit side just to the left of the camera.


* * *