Finally! --it's paint.

9-10 October 2014

I have been procrastinating the hull paint on this boat for an inordinate time.  This is really 'just because' --I truly haven't felt like investing the time and effort into it till now.  But I've had the gallon kit of Interlux Primekote for a while, just for when I decided to do it, and so I finally bowed to the constant encouragement of my friend and boatyard neighbor Jerry (C44 Second Alarm) and together we attacked this.

 

(The spots on the bottom are my repair of some hull cracks that had spread through the Pettit Protect barrier coating that I applied last year.  Discovering these was distressing; but I've been determined to have this boat done properly and so the Dremel took was applied right through it and WEST epoxy, with milled fibers as filler, was troweled into the gouges.  As of now it's really pretty good.)

 

Jerry did the rolling and I was going to try tipping it, for which I bought a couple of really good brushes, but we found that Primekote doesn't want to be tipped.  We also found that it should be thinned more than the 20% the label advises-- I approximated about 25% (or a little more) into each batch.  We mixed 5 batches of about 20 ounces each and this did a little more than two full coats of the hull.  Jerry was a champion with the rolling and really made the paint spread well with virtually no heavy spots.

 

Earlier pics will show the extensive repair on the transom.  Upon removing the center-mounted backstay tang, I discovered its load had sort of impressed upon the transom, creating a hollow.  I filled this with new 'glass and plenty of WEST epoxy with Microlight.  With Jerry's help I sanded the entire hull with 80 grit, and then 120 grit, using DryGuide, this marvelous black powder that, applied to the hull before sanding, illustrates clearly where your highs and lows are.  Sand it all off and it's fair-- and, amazingly, that stuff does not lie.  This hull is incredibly fair-- and, in some places, fairer than it was fresh from the factory!

 

I haven't seen this transom all one color since I brought the boat up to Delran!

 

This poor boat had numerous close encounters with pilings and the like, to the point where some PO cut off a section of bow rail to effect a repair.  I took this off again to repair his repair and left it off for the painting.  By some odd coincidence this is the very section of rail that needs to be cut down to accommodate the anchor roller (as it's tradition for sailboats to have the primary anchor rode to starboard).  The whole nose has been redone with 'glass, Microlight, milled fibres, and endless sanding.  Now in the bright white Primekote it looks almost done.

The holes formerly occupied by the hull-mounted running lights will be fitted with teardrop-shaped black Plexiglas windows, giving light to the forepeak locker and finishing off the bow in a familiar way.  I'm putting little blue LED lights in here (called 'docking lights' on the breaker panel) to represent Diana's personality.

* * *

It's been a long, cold, lonely winter.

The winter of 2013-2014 has been harsh to New Jersey. Most people of a certain generation are hard-pressed to recall more nasty weather. It hasn't been the frequency of snow, nor the intensity, but something like a combination of the two. We had two major power outages in the region and the township plowed exactly once in six major snowfalls. Plus I was commuting 52 miles each way to work at a marina on the Shore and lost plenty of time and income due to weather. Nearly nothing got done on Diana between early December and about five weeks ago.


Here are some updates, in no particular order.

Foredeck hatch

I finally got the foredeck hatch done (or done enough) and set it on the boat the other day, just before one of the rainfalls we've been having on and off all week.

The poor contraption has been kicking about for about three years. Here it is getting a coat of varnish after I plugged the screw holes in the two sticks on top. (They are aligned over the two ribs which stiffen the frame and the Plexiglas.) I had to take the mahogany down to about 80 grit in some places. Right now it has about three coats of Captain's Varnish on top and about five or six on the sides (on the frame).

 

Here it is (below) after I set it onto the hatch base. The construction of this is exactly as we do on the Cherubini 44-- it is essentially two boxes, a frame and a coaming, made separately. When you have fit the frame box to the deck, you slice off the top portion (in this case 2-1/4") with the table saw, rolling the thing over the blade to cut the four sides. This ensures you have a mated base and hatch. Once the base is installed on the deck, you install the coaming inside it. I set the front of the coaming back about 1/16", using some lauan doorskin plywood, to allow the bottom inside edge of the hatch to clear the coaming as it hinges open. I also slightly tapered the outside faces of the coaming, above the base, to provide clearance. Actually there is a bit more clearance than is necessary or desirable; but it's not bad.

 

As viewed in profile, the hatch base is probably too high. During my usual intellectual communing with my dad, I apologized to him for it. He would have had it a whole inch lower to the deck.

At 24 x 26 inches, this opening is sort of a forward "command center" from which one can lower or raise the anchor, navigate and deploy or stuff headsails. The dimensions also allow for the hatch cover to be unpinned from its hinges and lowered through the opening to stow it below-- a consideration I considered paramount and one which led me to increase the former molded coaming's opening (in essence I sliced out the whole molded coaming entirely).

Today I got to enjoy this in a light drizzle, which was actually pleasant. The translucent white Plexiglas allows majestic light below and even when only partially open allows adequate ventilation.

Electrical panel

I have since added the rest of the trim to this; this is a pic from a few days ago. Today I concentrated on wiring the guts of this panel. As you can see the electrical space is located along the hull shelf above the quarter berth, using the original faux-teak-plywood shelf and just adding a front and top.

 

 The small panel to the left (aft) is the 115VAC panel.  Below the double breaker is the slot for the battery-charger's breaker.

The two main 12VDC panels are for the lights and other circuits.  There is also the bilge-pump switch, voltmeter, fuel-level gauge and a 12VDC outlet.  The voltmeter reports the status of the three batteries (a two-battery house bank and one starting battery) by way of three push-button momentary switches.  There is a switch to turn on or off the fuel gauge as well (switch is not in this pic; it was installed today).

The two rotary switches forward of the double panels are selectors; one is on the running-lights circuit to choose between the masthead tricolor and the pulpit-mounted lights and the other one is on the cabin-lights circuit to choose between the white and red lamps.  In this way no one can activate a white light below when the boat is being navigated at night.  The two rotary switches are aligned with their respective master switches in the panel to their left, as though pointing towards their home circuits when they are in the "normal" positions.

Bookcase

I installed this a while ago but never got a decent pic of it. (This isn't really a decent pic either.) The bookcase is an alcove built into the head (aft end) of the starboard-side settee, under the galley counter. It is scaled for paperbacks of 6 x 9 inches and accommodates things like the Eldridge's, novels and certain tools manuals. There is a blue LED lamp inside, activated by a switch above the galley. The little plywood end (to the left in this pic) opens to a compartment outboard of the books where I can "hide" (stash) CDs and DVDs that are not immediately needed or already loaded into the computer or iPod.

 

Head compartment

Almost all the trim in the head has been installed. As built, the Hunter 25 did not come with a basin in the head; there was just an open bin above the footwell of the berth on each side. Diana's PO took out the floor of the starboard-side one and added a hanging bar so that coats on hangers draped into the footwell of the bunk. I restored a floor here and made two "duffel-bag lockers" for guests' gear. This pic shows the top of those lockers (without their access panels installed) and the trim.

 

To port I installed a proper basin for foot-pump pressure water.  The portion of the countertop aft of it lifts up to the old bin's original floor, providing a space about 4" deep for "lady products" (for my daughters) and other stuff that isn't needed every day.

The old-style black-based Whale faucet is mounted in a 7/8"-ID stainless-steel flat washer serving as a trim ring.  The other washer lying on the countertop was meant for the bottom but I haven't been able to get my (arthritic) fingers up into the access hole underneath to install it.  The aluminum tube of the faucet is a little tatty and I may opt to replace it later; so this is a job that will remain "temporary" "for now".

The lockers outboard of the sink are for towels (aft) and toiletries (forward). Right now they hold everything I took out of the galley lockers in order to finish those now.

In this picture I still owed the fiddle of the lift-up some varnish; but as of this writing it's been done.

The black conduit tubing will get tidied up. But due to the crossmember (on which the junction box for the spar wiring is mounted), the wire loom can't drop straight along the bulkhead; so it is led about an inch away along the cabin side and through a hole in the top of the locker. I did not make a fiddle here; the trim is just a common corner bead. It's too narrow a space to put anything on it anyway.

My mother, the accomplished seamstress, is making the curtains for these windows. They will span the full width of the space so that, when closed, they will be proper drapery that regularizes the oblong shape of the deadlights. The same will go for the main saloon as well.

I still have not connected the fresh-water lines to this sink. The holdup is solving the water-filter question. It's looking like I will install two undersink cannister types, one here and one in the galley. RVers tend to use a "pre-tank" filter, hooked up to the garden hose as they fill the tanks; but this requires that the water in the tanks is presumed good. Most of the bad-tasting water I've encountered has gone bad in the tanks. I'd rather apply the charcoal and coconut-shell filtration at the tap(s), so I'm looking into Purete and Whirlpool compact filters. The one I've got in mind for the head sink is meant for icemakers and its connections are for 1/4" tubing. I may be able to do without the small-ID "quick connectors" and adapt it to 3/8" supply hose for the head sink. The galley can get a 3/8" one adapted to 1/2" supply hose.

* * *