Moving day

24 October 2014

I have not been happy with the boat's being where it's been.  This is sort of the 'swamp' of the yard.  Well-- it is not really a swamp-- Diana has been sitting on good solid packed gravel-- but the ground immediately beside her is low and tends to fill up in any rain.  This, in addition to the constant mosquitoes, makes doing boat work after 4.00 pm and on weekends less than fun.  So I contracted the guys to relocate Diana to a drier, happier place, especially with regards to facing another (her last?) winter on land.

Here in the Northeast, when placing a boat for the winter season, it is best to situate her nose-into the weather.  This is better for the boat, for any covers, for the stowage of gear on deck and on the ground, for persons entering the boat in the off-season, and for a host of a million other reasons.  Diana, especially, with her low-profile deck and cabin, heads to weather very well-- but all my covers and the cockpit have taken a beating over these (too many) years sitting stern-to the weather, which here in Delran comes to us on a direct line from Philadelphia (bearing from W/SW) in summer and from W and NW in winter.  The compass in the bulkhead shows her facing E/SE.  Enough said.

This is Diana's old spot, in 'The Swamp'.  Here Jerry's C44 Second Alarm has been moved to his new spot and I was standing, for the first time in two years, where his boat had been.  Together these boats and the others in this photo weathered Superstorm Sandy and all the rest.

Now I know how these guys work.  The guys from Riverside Marina come over, back the hydraulic boat carrier to the front of your boat, and then-- wait for it-- remove all the stands.  I mean all of them but the very back and the very bow.  I've seen them do this even on windy days, with the rig up.  Yikes.

Watching them do this with a C44 or Ben's Rhodes Reliant (with that narrow transom!) is unnerving.  Watching them do it with my own boat is an automatic case of the heebie-jeebies.  I was so paranoid that I subtly replaced the stands in the very back with a pair a little closer forward, though they were not at any bulkhead, just to persuade them to leave those as the last two.  But they moved them back (to right where they were before), saying they couldn't get the truck under it.  I was near fits.

Then, to really bring on the stomach acid, the forward pads on the truck would not find the boat.  I've seen this thing in action many times but always thought that for smaller boats the pads would angle inwards.  Apparently, they don't.  The picture shows the back ones too far forward and too low, the front ones way too high, and the keel (read that: whole weight of the boat) on a 3-inch-wide strap spanned between the wheels of the truck thing.  Sheesh.

Meanwhile, between snapping photos (which I did not really do so much) I was worrying that the pads in front are pushing against the v-berth shelf, probably popping off the rode-locker bulkheads I 'glassed there, and definitely scraping off the newly-applied primer paint.

Then Jeremiah in the shop says, 'It better not be scraping off the paint.  It's epoxy.  If they're scraping it off, it wasn't applied right.'  And it was applied right.

End result: Diana arrives across the yard safe and sound.  There was a problem with blocking her, as the guys could not get the strap out from under the keel without blocking the keel bottom in the same place as before-- meaning I still can't scrape, prime and barrier-coat the very bottom.  But I can sort that out another day.  The bulkheads forward were fine (of course).  And the epoxy primer survived very well-- the traces of black wiped off with one hand while I was talking on the phone.  No worries.

In this location the barn part of the shop will block most wet snow.  The weather now comes from off Diana's nose or from slightly to port.  I will have this shrink-wrapped by the end of November (after topcoat on the hull).

The few odd places where the barrier coating was sanded through are the repairs I had to make for the cracks; this is reported elsewhere.  Jerry gave me some leftover stuff so I may not need to go into the quart kit of Pettit Protect that I bought for these (and for the rudder).  The gray cover is because of the instrument holes in the back of the cabin and because the forward edge of the hatch hood is still open (needing woodwork, the last major job to be done to the deck).

On the deck there is a bucket upside-down over the mast step.  The step will be removed for the deck to be painted and then reinstalled with 5200.

The holes forward, where the running lights were mounted, are to be covered with Plexiglas panels, as Diana's eyes (more on this 'secret' later). 

The foredeck hatch is slid open in this picture.  I have to put hinges on it, then remove them, then varnish the whole thing, which, with the boat under shrink-wrap, can easily be done in the shop.

Little Diana likes her new spot in the sun!

In the background can be seen the CY spars rack, welded and bolted to the side of the former storage trailer that is now the lumber-storage room for the shop.  On this rack are C44 spars, the ones for Dave's Reliant, and a few others.  Jeremiah puts each up there with the forklift (another operation that has to be seen to be believed).

I prefer six stands, not four (not counting the bow) because it's simple to pull one down to paint the bare spot.  The plywood steps came over from Diana's old place because I used them to fill and fair the old bow damage and will use them now to reinstall the section of toerail, the stem fitting and the anchor roller.  In this photo I have not yet moved the spars and the workbench to the new spot.

The half-gallon of iced tea is Turkey Hill from 7-11-- the very best cold green tea you can get!  :)

* * *

Finally! --it's paint.

9-10 October 2014

I have been procrastinating the hull paint on this boat for an inordinate time.  This is really 'just because' --I truly haven't felt like investing the time and effort into it till now.  But I've had the gallon kit of Interlux Primekote for a while, just for when I decided to do it, and so I finally bowed to the constant encouragement of my friend and boatyard neighbor Jerry (C44 Second Alarm) and together we attacked this.

 

(The spots on the bottom are my repair of some hull cracks that had spread through the Pettit Protect barrier coating that I applied last year.  Discovering these was distressing; but I've been determined to have this boat done properly and so the Dremel took was applied right through it and WEST epoxy, with milled fibers as filler, was troweled into the gouges.  As of now it's really pretty good.)

 

Jerry did the rolling and I was going to try tipping it, for which I bought a couple of really good brushes, but we found that Primekote doesn't want to be tipped.  We also found that it should be thinned more than the 20% the label advises-- I approximated about 25% (or a little more) into each batch.  We mixed 5 batches of about 20 ounces each and this did a little more than two full coats of the hull.  Jerry was a champion with the rolling and really made the paint spread well with virtually no heavy spots.

 

Earlier pics will show the extensive repair on the transom.  Upon removing the center-mounted backstay tang, I discovered its load had sort of impressed upon the transom, creating a hollow.  I filled this with new 'glass and plenty of WEST epoxy with Microlight.  With Jerry's help I sanded the entire hull with 80 grit, and then 120 grit, using DryGuide, this marvelous black powder that, applied to the hull before sanding, illustrates clearly where your highs and lows are.  Sand it all off and it's fair-- and, amazingly, that stuff does not lie.  This hull is incredibly fair-- and, in some places, fairer than it was fresh from the factory!

 

I haven't seen this transom all one color since I brought the boat up to Delran!

 

This poor boat had numerous close encounters with pilings and the like, to the point where some PO cut off a section of bow rail to effect a repair.  I took this off again to repair his repair and left it off for the painting.  By some odd coincidence this is the very section of rail that needs to be cut down to accommodate the anchor roller (as it's tradition for sailboats to have the primary anchor rode to starboard).  The whole nose has been redone with 'glass, Microlight, milled fibres, and endless sanding.  Now in the bright white Primekote it looks almost done.

The holes formerly occupied by the hull-mounted running lights will be fitted with teardrop-shaped black Plexiglas windows, giving light to the forepeak locker and finishing off the bow in a familiar way.  I'm putting little blue LED lights in here (called 'docking lights' on the breaker panel) to represent Diana's personality.

* * *

More on the inner-staysail bulkhead

In this pic I have painted the bulkhead but have not attached the fuzzy hull liner, the bow-locker door, or the chain-locker doors.   The hull liner is the roll wrapped in cardboard paper lying on the bunktop.

I am not going to paint the faux-teak bow-locker bulkhead, just for old-times' sake, to show the original fabric of the boat as-built.  The small holes in the stem are awaiting the fitting of the stem fitting (see here).

In this pic also can be seen my method for securing the forward hatch: small cord tied to eyestraps on the hatch, the same as my dad did on our 31' plywood yawl in 1962.

The fiddles on the hull shelves, port and starboard, are made high enough to make bins.  These will hold sailbags (it's a small boat!) and other stuff the way the old ones (about 2" high) never would have done.  Above, as though a facia covering the toerail bolts, will go a similar board to hold hooks from which sail bags, fenders, dock lines and other things can be hung.  As such, this space becomes a bona-fide forepeak, nothing like what's found on even much, much larger yachts.

The varnished board down the center of the underside of the deck is, in this pic, just sort of stuck there.  It is meant to catch the bolts and backing plates of the foredeck cleat, the inner-forestay's attaching plate, and the anchor winch.

I am not happy about the gaps along the top of the chain-locker bulkheads (to port and starboard here) against the underside of the deck but will leave the fitting of some varnished trim for some later date! 

* * *

Diana's new stemhead fitting

I never liked the three-legged Hunter 25 pulpit and meant to replace it with something cooler from the very start.  This would mean cutting off the 7/8" stainless-steel stud from the stemhead fitting and polishing it over; but as Diana's PO had put her into some kind of close encounter with a piling, the original stemhead fitting was quite mangled and badly restraightened.  So I determined to make a new one.

I designed a very nice replacement part for this but found no one to make it at a reasonable price.  Then I happened to stumble across one on the Racelite web page and ordered it.  Though the dimensions on the site represented an adequate part, the actual thing seemed to represent them only nominally-- the thickness was not a true 1/8" and the length was entirely too short.  Rather typically I sat on this problem for over a year, working on other things, while I contemplated some solution.

Finally I ordered some flat stock, cut it to length, and sent it out to the local welders' with a pattern of the correct angle.  The part I received was simply beautiful.  I have begun to polish it and will finish it off before it's permanently installed.

 

You can see how the original part was only about 60 percent as long as it needed to be along the stem.  The flat stock welded to the part effectively doubles the thickness for the first three holes.  It is true that the tang for the forestay is still of the thin (original) stock; but as it's already thicker than were the shroud tangs I'll install it as it is and see if, as the rig is tuned, I get any elongation of the hole.  If that will be the case (which I doubt) I'll have it remedied with more welding.  As this Racelite part is meant for 20-to'22-footers, and as it's already meant to carry the load of 1/4" clevis pins, I'm betting it won't ever be a problem.

 

In this pic I have set the part on the bow to check the fit.  Thanks to my template the welder's work resulted in a perfect fit. You will see the gap behind the very top of the fitting-- this requires attention.  If I were to mount this as-is, two things would happen: Diana's J measurement (foot of the headsail) would be longer than that of a stock Hunter 25 by about 7/8"; and the natural stresses of a tuned and ruggedly-used rig would attempt to bend the fitting aftwards, putting the single screw through the deck into a shear load, and some distortion would occur.  This is why it is never wise to suspend rigging attachments over air, as would be done here.  I will fabricate a little block for in this gap, just something to support the compression load, and 'glass or epoxy it into place prior to paint and prior to attaching this fitting.

The horizontal pencil lines are marking where the mounting holes will go.  Only one of the original holes lined up.  I have a mahogany backing block for this, to be bedded in 5200 inside, and will drill new holes for the 1/4-20 hex-head cap screws.  Hex-heads are best for this sort of thing because you can put a ratchet and socket on each one and really tune them well.  Large-scale Phillips and, worse, slotted-head screws are really kind of pointless after a while.  A larger screw implies a larger load which means installation torque matters more.  No one can apply appropriate torque with a screwdriver handle.  I think the only reason people dislike hex-headed cap screws is because they make the boat look like Frankenstein's monster.  Personally, I like the look.  It's its own aesthetic.

The evident damage to the bow was from the PO.  The starboard-side toerail was cut to facilitate the fiberglass repair and reattached.  Coincidentally, this piece will have to be cut down to accommodate the anchor roller.  I'll fill the seam in the toerail with black 4000-UV to minimize the appearance of a crack.  Much of the old fiberglass repair was faired over with 3M filler (the grayer stuff).  The darker brown-olive is raw fiberglass from my sanding.  I have filled all the imperfections with both Evercoat 27 and epoxy and after painting with epoxy paint (Perfection or Brightside) this won't be visible or vulnerable.

The brown thing above the deck is the work-order tag from the welders'.  Mistakenly they wrote it up as being for my cousin Dave's shop; but this was my project and I contracted and paid for it.  (This happens a lot, actually.)

Sales pitch #1

If any other H25 owner is interested in having one of these parts, I will be happy to supply it.  It does, however, require a 4-legged pulpit; though I'd consider that an improvement.  I've designed an updated bow rail for Diana, along the lines of a J27's, complete with step-through end, varnished-mahogany seat/step with nonskid, and mount for Aqua Signal running light; though I'll be installing a plain-Jane castoff pulpit from another boat for the short term.

Sales pitch #2

Yes; the boat beside Diana, evident in one of these pics, is one of her sisters-- in this case a fellow February 1974 boat, this one the later trunk cabin/pop-top model.  They are both of the same series, Diana being number 027 and the other boat being 140.  At that time Hunter had two production lines of H25s at their Marlboro, New Jersey, plant; and I believe that the "0" signified the period's production series of "blister-canopy" or "flush-deck" models and the "1" signified the trunk-cabin models. If these boats were not on the production floor at the same time, they are probably not more than two weeks apart in age.

I have been referring to this other boat as "the sweet sister" and  hope to enter negotiations with her owner to take over her care and to restore her-- for she is still, even with an inadequate cover, in better condition than Diana was when I first found her and would represent a pretty easy, quick and profitable "quick fix" and resale.  She'll need some deck-core repair, paint, new cushions and upholstery, lifelines and probably cordage; and I do not know if there is an engine available.  But it wouldn't take much more than that for her to go sailing again.  As soon as Diana goes in I will have this boat shrink-wrapped and set a dehumidifier in her, to help preserve her.  Anyone interested is welcome to get in touch.

* * *