The crucial duty of the compression post.

A Hunter owner asked me about rebuilding his compression post; and my comments on the Hunter Owners Web in response are probably worth something; so here they are--

http://forums.hunter.sailboatowners.com/showthread.php?p=996161#post996161

And here are some pics that go with it--

 

This is what Hunter gave H30 owners-- it is NOT a compression post.  This is the view looking through the bilge.  Apparently this corroded object purports to support a piece of mahogany, which supports a piece of aluminum, which supports the plywood sole, which supports a teak block of some kind-- and all of it transmitting the load to precisely the wrong place-- the top of the keel.


Here is my post; and below is how it is supported.

The pic below shows Diana's bilges before I installed the sole (half of it is in place to starboard). Thejoists are all 5/4 mahogany, cut and fit to the hull and bonded with 5200; the post stands on a doubled one abaft the main bulkhead. Note that none of them are in contact with the actual bottom of the hull. The goal was to spread each one's load to as much surface area as possible. Note the limber holes and bilgewater spaces, access for keel bolts, and the central joist having cleats to accommodate the leg of the drop-leafed table (looks like a tripled joist). The part on top of the can that looks like 2/3 of a joist goes in the head compartment.

The electric bilge pump goes in the space farthest aft in this view.  The manual pump's pickup goes in the farthest forward space in the main cabin.

Under each settee is a water tank and a house battery, so all this weight goes here, not to the ends. The red and yellow wires tie the batteries together as one bank.  The orange wire is for the voltmeter.  These will be restrained in fairleads later.

The PVC freshwater manifold (second big space from bottom) connects the two tanks, one under each bunk.  Unfortunately the head sink will feed from only the port one.  There are independent shutoffs, port and starboard.  The valve to the back is the drain, so either tank can be selected to either drain or supply the galley sink.  The black thing is a particle strainer.  Under the galley sink goes a proper cartridge filter.

The hull drain has since been added, under the tanks' drain.  It is removable from inside-- the better to facilitate inspection and maintenance (and to streamline the underbody).

The brown dirt is pretty much bonded into the spilled epoxy and will have to be sanded off and painted in Bilgekote.

 

* * *

Head compartment

In these photos this is far from being done; but I was just fooling about with the camera and took some photos of the head area to record progress.


This is the head sink, which, as all H25 owners know, the boat did not originally come with.

The stainless-steel basin came from an old Chris-Craft; I bought it on eBay for $19.00.  Its drain goes through the forward bulkhead-- to get out of the foot area-- and then to a trap and down to the drain seacock.

The after portion of this countertop (to the left) lifts up for access to a 4-inch-deep compartment above the foot of the bunk.  The two openings outboard of the sink are for toiletries and towels.  The little mahogany stick on the forward bulkhead, inside the locker, is the cleat for the shelf in there.  The shelf divider is sitting against the hull.

I put the tissue dispenser in there to calculate the space for it; but I certainly won't rely on a cardboard tissue dispenser to be kept in the head, under the large foredeck hatch, aboard a 25-ft boat!

There is no headliner or hullliner in place in this photo.  The trim is not installed here either.

The wiring isn't really this messy-- it's just dangling down from the connections block above this doorway where the spar wiring enters the cabin and the cross-cabin circuits pass by.  When it is connected properly you won't see the danging bits in and out of the lockers.


This Wilcox-Crittenden Head-Mate toilet was given to me by a guy called Bill who was working on his friend's boat in Hancock's Harbor, NJ.  I saw it sitting outside the boat on a Sunday and left a note on it: 'If you are getting rid of this toilet, call me and I'll take it.'  The guy called me as soon as he returned to the boat.  It pumps perfectly well-- they must have been switching to either a larger bowl or just an electric one.  The intake/flush lever is a little rusty; that's all I can find wrong with it.

I had intended to mount my existing 'Frankentoilet' with the crossover sanitation pipe underneath this blue shelf; so the shelf is mounted a little higher than it would otherwise be.  Unfortunately this toilet's pump doesn't mount on the level; it mounts at a slight angle (like a modern Jabsco) on an angled flange on the crossover pipe.  So I can't mount this pump on the shelf, with the crossover pipe underneath, because it won't sit flush.  I have no idea why Wilcox did it like this.  I really wish I were reusing the original Raritan Compact Mk I; but this is similarly 'retro' and works fine-- and best of all the price was right.

The two little openings under the shelf are meant for access to the bolts; and this was supposed to accommodate the crossover pipe underneath so these would allow for cleaning out as well.

Behind the toilet the black ring is a Starboard trim piece around the exit pipe (PVC) leading to the holding tank.

The all-plastic Rubbermaid tool box is actually in its intended place-- this V-berth area has become a true forepeak, having room for only one to sleep but getting equipped with a tool box, workbench, hanging locker, microwave oven, plenty of outlets for charging cordless tools and possibly also a fresh-water supply tank for flushing the toilet. The holding tank is underneath, with most of the plumbing and all but one of the boat's through-hulls.  And that's in only the aftermost 26 inches of it! [wink]

The mahogany in the foreground is the backup to the compression post, underneath where the maststep really is.  It's a piece of the stock I cut for the cabintop handrails, but here it is solid except for only one hand hole (through which the vacuum cleaner's cord is running).  I gauged this hand-hold for someone sitting on the potty and only after installing the stick I realized that the head door's latch has to go at the very same elevation-- so when you reach through it you will stub your fingertips on the edge of the latch plate.  Oh, well.

At the time this was taken the lockers behind the toilet were taken up with the stereo, the outlet strip and the lift-out panels for all the lockers about the boat.

The bronze Barlow selftailing winch (vintage 1977) is a leftover from Warren Luhrs' C44 cutter and served as a doorstop in my mother's bathroom for about 20 years.  It's now slated to be the foredeck-mounted anchor-rode winch for a first-generation Hunter 25 called Diana.  Funny how things turn out!

Here is an 'aerial' shot of this space, minus the toilet, taken from the foredeck hatch opening. 

The door jamb, to the right, was excessively tedious.  It is a T-section and has to fit a very awkward three-sided space and accommodate the natural crookedness of the boat as-is.  It turns out that the face of the head's sink cabinet (side of the port-side berth's footwell) is neither in one plane (it's twisted) nor parallel to really... anything.  Fitting delicate mahogany (the lower portion of that stick is 5/16" square) to a crooked boat is an exercise in near-futility.  But I got it to fit!


The threshold of this doorway is somewhat more robust.  If it appears crooked, it's because the main bulkhead of the boat is not square to the centerline.  Believe it or not that threshold is in the only place it can be to make the (not yet built) door work.

I still have to countersink those screw-holes to fit them with plugs; but I'm keeping it as removable in case something happens with the door later.

The rough plywood sole is only temporary.  The finger-hole, however, will be in the finished mahogany panel.  It's the drain for the space, as there'll be a shower hose here too.


The black square is the pedal for the Whale Gusher foot pump for the head sink.  It feeds from only the port tank, however, despite being likely to be the most-used water source in the boat.

In the foregound (top right of photo) you see the coaming for the foredeck hatch, not yet varnished.

I like the deep-blue/white/black/stainless/mahogany decor theme of this boat.  It's bright, cheerful, nautical and traditional.

* * *

Some inconveniences are beyond counting

I once told my young brother-in-law, as he was building some plastic model airplane and complaining about glue on his fingertips, that to do a good job sometimes you have to love your project more than you care for your self.  This is especially true when it comes to convenience-- after all, most of the things we love are patently inconvenient.  And yet we pursue them anyway; and in this pursuit is how we acknowledge their value to us.

This photo is not great; it's intended to show the nice fat mahogany splinter I got in my foot.  (How? --I wasn't even barefoot.)  In this one week I got this splinter and another as well, tore my fingertips on a jigsaw blade (it was not running), jammed the meat of my hand in the drill-press chuck and mysteriously gashed my leg which bled all over the project in process.

The West Marine sticker is on my daughter's laptop.

Here is the top of the cabin, with no hatch or hatch shroud in place, the day I was fastening down the new hatch-slider rails.  The green tape along a piece of wood is a dam to keep epoxy from coursing down the side of the cabin and over the windows (already let that happen once, so never again!).  I had noticed a stickiness whenever I was kneeling a certain way but in the semi-mad rush to get the sticks into position and screwed down I attributed it to something stuck to my leg.  Only when I was done the most urgent part of it did I happen to notice the red stuff, which I then concluded was blood.

That's the foredeck's hatch coaming in the distance.  At the time of this photo the hatch shroud was being used to cover up that opening-- that's it even farther beyond.

Below you can see something of the main cabin, the compression post, the settee and head trim, and whatnot.


So I took this photo downwards at my leg, probably just to record the solution to the mystery.

Here I am standing up on the quarter berth, my other foot on the ladder step.  The quarter berth is (at this time) the current lumberyard.  The gap below my foot is the 'wet locker,' the one place inside the accommodation that goes straight to the hull skin itself.  Over this I would like to make a panel of slats, like the white-pine ceiling we make for C44s.  On the side of the ladder, behind my leg, goes the stainless-steel double hook to hang up wet foulies.  On the teak cabin face behind me is already another of these hooks.


You can see the cooler under the bottom shelf of the ladder; its cover is accessible when you lift the shelf.  A Fastpin stuck through a hole in the ladder side holds it up.  It's made so that if one should descend the ladder while the shelf is up the shelf won't stick out so far so as to catch a heel and break off-- although it does mean there won't be a second shelf in place for the one coming down.

Also two sections of the three-part cabin sole are visible here.  At the time of this photo the center section is just rough plywood-- it'll be varnished mahogany later.

* * *