Head compartment

In these photos this is far from being done; but I was just fooling about with the camera and took some photos of the head area to record progress.


This is the head sink, which, as all H25 owners know, the boat did not originally come with.

The stainless-steel basin came from an old Chris-Craft; I bought it on eBay for $19.00.  Its drain goes through the forward bulkhead-- to get out of the foot area-- and then to a trap and down to the drain seacock.

The after portion of this countertop (to the left) lifts up for access to a 4-inch-deep compartment above the foot of the bunk.  The two openings outboard of the sink are for toiletries and towels.  The little mahogany stick on the forward bulkhead, inside the locker, is the cleat for the shelf in there.  The shelf divider is sitting against the hull.

I put the tissue dispenser in there to calculate the space for it; but I certainly won't rely on a cardboard tissue dispenser to be kept in the head, under the large foredeck hatch, aboard a 25-ft boat!

There is no headliner or hullliner in place in this photo.  The trim is not installed here either.

The wiring isn't really this messy-- it's just dangling down from the connections block above this doorway where the spar wiring enters the cabin and the cross-cabin circuits pass by.  When it is connected properly you won't see the danging bits in and out of the lockers.


This Wilcox-Crittenden Head-Mate toilet was given to me by a guy called Bill who was working on his friend's boat in Hancock's Harbor, NJ.  I saw it sitting outside the boat on a Sunday and left a note on it: 'If you are getting rid of this toilet, call me and I'll take it.'  The guy called me as soon as he returned to the boat.  It pumps perfectly well-- they must have been switching to either a larger bowl or just an electric one.  The intake/flush lever is a little rusty; that's all I can find wrong with it.

I had intended to mount my existing 'Frankentoilet' with the crossover sanitation pipe underneath this blue shelf; so the shelf is mounted a little higher than it would otherwise be.  Unfortunately this toilet's pump doesn't mount on the level; it mounts at a slight angle (like a modern Jabsco) on an angled flange on the crossover pipe.  So I can't mount this pump on the shelf, with the crossover pipe underneath, because it won't sit flush.  I have no idea why Wilcox did it like this.  I really wish I were reusing the original Raritan Compact Mk I; but this is similarly 'retro' and works fine-- and best of all the price was right.

The two little openings under the shelf are meant for access to the bolts; and this was supposed to accommodate the crossover pipe underneath so these would allow for cleaning out as well.

Behind the toilet the black ring is a Starboard trim piece around the exit pipe (PVC) leading to the holding tank.

The all-plastic Rubbermaid tool box is actually in its intended place-- this V-berth area has become a true forepeak, having room for only one to sleep but getting equipped with a tool box, workbench, hanging locker, microwave oven, plenty of outlets for charging cordless tools and possibly also a fresh-water supply tank for flushing the toilet. The holding tank is underneath, with most of the plumbing and all but one of the boat's through-hulls.  And that's in only the aftermost 26 inches of it! [wink]

The mahogany in the foreground is the backup to the compression post, underneath where the maststep really is.  It's a piece of the stock I cut for the cabintop handrails, but here it is solid except for only one hand hole (through which the vacuum cleaner's cord is running).  I gauged this hand-hold for someone sitting on the potty and only after installing the stick I realized that the head door's latch has to go at the very same elevation-- so when you reach through it you will stub your fingertips on the edge of the latch plate.  Oh, well.

At the time this was taken the lockers behind the toilet were taken up with the stereo, the outlet strip and the lift-out panels for all the lockers about the boat.

The bronze Barlow selftailing winch (vintage 1977) is a leftover from Warren Luhrs' C44 cutter and served as a doorstop in my mother's bathroom for about 20 years.  It's now slated to be the foredeck-mounted anchor-rode winch for a first-generation Hunter 25 called Diana.  Funny how things turn out!

Here is an 'aerial' shot of this space, minus the toilet, taken from the foredeck hatch opening. 

The door jamb, to the right, was excessively tedious.  It is a T-section and has to fit a very awkward three-sided space and accommodate the natural crookedness of the boat as-is.  It turns out that the face of the head's sink cabinet (side of the port-side berth's footwell) is neither in one plane (it's twisted) nor parallel to really... anything.  Fitting delicate mahogany (the lower portion of that stick is 5/16" square) to a crooked boat is an exercise in near-futility.  But I got it to fit!


The threshold of this doorway is somewhat more robust.  If it appears crooked, it's because the main bulkhead of the boat is not square to the centerline.  Believe it or not that threshold is in the only place it can be to make the (not yet built) door work.

I still have to countersink those screw-holes to fit them with plugs; but I'm keeping it as removable in case something happens with the door later.

The rough plywood sole is only temporary.  The finger-hole, however, will be in the finished mahogany panel.  It's the drain for the space, as there'll be a shower hose here too.


The black square is the pedal for the Whale Gusher foot pump for the head sink.  It feeds from only the port tank, however, despite being likely to be the most-used water source in the boat.

In the foregound (top right of photo) you see the coaming for the foredeck hatch, not yet varnished.

I like the deep-blue/white/black/stainless/mahogany decor theme of this boat.  It's bright, cheerful, nautical and traditional.

* * *

Lost Star Yacht Club’s restoration-project quiz

An informative and entertaining self-examination


Anyone involved in restoring his own boat for any length of time will readily recognize the answer for each that best represents reality here!
(Note: as though you can’t guess, ALL of these are based on real-life experiences.)



The best-laid plans

Apparently, the previous owner of your boat was

1. A dedicated yachtie who kept it in pristine order
2. An older guy who let it go during the last few years he had it
3. A complete idiot

Carefully-drawn plans or instructions for your intended projects

1. Serve a valuable purpose in organizing, scheduling and budgeting the work
2. Give a general idea which usually gets changed once you start the work
3. Are likely to be left in the bathroom at home and thus disregarded in place of ‘just winging’ it when you’re already at the boat to work

Schedules and budgets are

1. Valuable guides to keeping a sense of sanity and proportion
2. Seldom absolute
3. Completely pointless

The last time you had a completely new idea about what to improve on the boat was

1. The last time you sailed it
2. Right before you began an organized plan of restoration
3. Five minutes ago

Parts catalogues will

1. Be worth browsing to what’s available and what can be ordered
2. Be important sources of ‘how-to’ information
3. Get comprehensively marked-up with underlining, highlighting, circling, arrows and diagrams as well as notes and gift hints to family members who will really never see or heed them

Tools of the trade

The average yacht restorer’s tools and supplies are stored in

1. A shiny metal rollaway tool chest with locking doors
2. A handmade mahogany-and-plywood toolbox
3. A mismatched collection of eleven (or is it twelve?) lidless containers and damp cardboard boxes, organized, if at all, in such a way that Rube Goldberg, Charles Manson and PeeWee Herman would consider it crazy

Your stepladder is

1. A new orange fiberglass one from Home Depot
2. An old aluminum one that has seen many years of dependable service
3. A really crappy wooden one that was surreptitiously ‘borrowed’ from some other guy in the boatyard

The tool vital to starting the next job will mostly likely be found in the

1. Tool box
2. Last place the tool was used
3. Bilge

Your electric extension cord is

1. A brand-new blue one, 100 feet long, 12-gauge, with a heavy-duty plastic recoiling reel and a molded-in 4-outlet box with circuit breaker
2. The two lengths of orange cord relied-upon for the hedge clippers at home
3. Possibly more duct and electrical tape than actual electrical insultation

A flashlight’s most common function is to

1. Illuminate poorly-accessible areas
2. Attack would-be burglars or wasps’ nests
3. Store dead batteries until you decide to throw them away

The usual condition of the average cordless drill/screwdriver’s batteries is

1. Both at full charge as soon as possible
2. The one in the unit dead, the other one charged and waiting in the charger
3. The one in the unit dead, the other one, which died last night, nowhere to be found

Wood plugs are frequently sealed in the screw holes using

1. Weldwood wood glue and an overnight drying process
2. WEST epoxy and an acid brush
3. The varnish, when you noticed the missing plug(s) right after you started to brush it on

Your boat-work shoes are

1. High-quality leather moccasin-type deck shoes
2. Sturdy, sensible work boots
3. A pair of ripped, stained and punctured CVOs with the soles completely blown-out or held together with duct tape; and your wife wonders why on earth they are still in the house

Rubber gloves and dust masks are

1. Essential, for safety and hygiene
2. Frequently necessary for really ugly jobs
3. Unheard-of

The procedures

You tend to have help in this project

1. Most of the time
2. About half the time
3. Pretty much never, unless you count the times when somebody from the yard comes by with a beer and talks while watching you work

‘Cutting corners’ in quality is

1. To be avoided
2. Sometimes necessary
3. Totally acceptable, so long as the task gets done

When you encounter a necessary task involving an area of expertise in which you have no experience, you will

1. Seek help from an expert
2. Read up on the procedure and treat it as a learning experience
3. Get out the tools and epoxy and start doing it

During a restoration, the bilge usually contains

1. Dirt and liquids, till they are cleaned or pumped out
2. Hoses and wiring that would be unsightly if run elsewhere
3. Wet pencils, locknuts and expensive electrical connectors you thought you mislaid and have had to buy again

When working on the boat, trash is

1. Stuffed into a 5-gallon paint bucket which is emptied at the dumpster each evening
2. Brushed into a corner of the cabin sole or cockpit
3. Pitched out the companionway hatch at the spur of the moment; and may God have mercy on the poor people who may have stopped below to look over the boat

Some of the fiberglass lay-ups in your boat may contain

1. Small air bubbles
2. Dust or wood chips
3. Sandwich lettuce, Dr Pepper and your blood

When installing fittings on spars, you will use

1. One thread tap, carefully maintained with oil
2. Maybe two or three taps
3. So many taps that you must make the 20 minutes’ trip from the boatyard to the auto-parts place several times a weekend

When you are kneeling or balancing on hull timbers to install new cabin-sole panels, the electric drill that gets in your way will most likely end up with the point of the new spade bitt in

1. The bilge
2. Some finished woodwork
3. Your leg

The usual procedure for electrolytically isolating stainless-steel fittings from aluminum spars involves

1. Applying nonconductive thread-locker liquid to the threads
2. Smearing both sides with white lithium grease
3. Sticking a piece of white electrical tape under the part before screwing it down

When cutting plywood outside, the rain will begin

1. The moment the pieces are cut
2. In the middle of the job
3. As soon as you have run the extension cord, clamped down the part, and switched on the jigsaw

The most valuable application of white Krylon is for

1. Gas grilles, bicycles and outdoor furniture
2. Models made of metal parts
3. Anywhere you neglected with Durawhite, Bilgekote, or Awlgrip when it’s time to put the boat in the water

When cutting Plexiglas, the typical experience will involve

1. A slow, clean cut with the jigsaw
2. Easily peeling off the protective paper backing
3. Having the blade get stuck in the middle of the cut when the material melts itself back together and then using hacksaws, grinders or lots of sanding to ultimately finish the part

When cutting G-10, you should use

1. A brand-new, fine-toothed jigsaw blade
2. An old blade that is almost ready to be thrown away anyway
3. Someone else’s blade (and saw)

With the spars out of the boat, the usual procedure for reeving new halyards involves

1. Carefully ‘sewing’ and whipping the braided messenger line to the new halyard
2. Tying the messenger line to a paperclip ‘buried’ into the new halyard
3. Hastily wrapping the messenger line to the new halyard with about half a roll’s worth of electrical tape

The 5200 is usually applied

1. In assemblies that must hold out seawater and are not likely to be dismantled in the regular course of maintenance
2. For anything and everything that goes together
3. All over the cabin sole, your knees, the clipboard, most of the tools and half of the sub sandwich you had intended to finish

The usual disposition of an unfinished tube of 5200 is to

1. Cap it so it stays airtight and store it in a cool dry place
2. Stick a machine screw down the nozzle and wrap tape over the end
3. Leave it where you last used it and expect to throw it away next week after the remaining half has cured in the tube

When painting decks or soles, the usual experience involves

1. Careful planning so that you can work from a ‘wet edge’ in painting from one end to the other
2. The occasional oversight requiring that you lean over wet paint to reach neglected dry spots
3. A completely disorganized nightmare involving spills, runs, blots and numerous opportunities to wear your work home

When the tarp that covers the boat needs to be changed, the wind will pick up

1. As soon as the new tarp is tied down
2. As soon as you arrive at the boatyard to do it
3. As soon as you get the old tarp stuffed into the dumpster and begin spreading the new one over the cabintop

Your primary motivation for doing painstaking work is one of

1. Interest in the value of your investment
2. Concern for the durability of the boat for the future
3. Pride, to demonstrate your superior ideas and craftsmanship

After-work bathing typically entails

1. A long refreshing shower
2. A rush to finish and get on to other tasks
3. Dishwashing liquid, Fast Orange and Scotch-Brite to remove all the paint, 5200, epoxy and resin from your raw skin

Beat the odds

The likelihood of damaging or dislocating a seacock is inversely proportionate to

1. The cost of the seacock
2. The importance of the supply line attached to the fitting
3. The need to replace it

The likelihood of drilling a hole through a spar or bulkhead and breaking into a length of electrical or plumbing conduit is inversely proportionate to

1. The cost of the conduit
2. The importance of the hole you’re drilling
3. The amount of time left before the Travel-Lift comes

The likelihood of tossing a screwdriver up into the boat and damaging something is directly proportionate to

1. The cost of the screwdriver you toss
2. The proximity of the object it hits
3. The amount of work you put into what it hits

An example of an unexpected negative correlation may exist between

1. The quality of the varnish job and the cost of the foam brushes
2. The cost of a VHF radio and the time it takes to receive it from the supplier
3. The time and effort you take to install the paper-towel holder and the importance of the paper-towel holder to the overall project

The costs

The way to really recognize a yacht owner who is performing his own work is by

1. His smile of sublime satisfaction at the launching banquet
2. His nearly-empty wallet at the end of the weekend
3. The 5200 under his fingernails at church

One of the most humiliating things about taking so long to restore your boat is

1. Your friends’ nagging impatience to go sailing
2. Paying 12-month dry-storage contracts
3. Discovering that the state-of-the-art CD stereo system and FireWire computer network you installed 4 years ago have become obsolete before you got to use them

One way to be sure you’ve spent too much money on parts is by

1. The smiles on the faces of the staff at West Marine
2. Your wife’s interrogation about the Visa bill
3. The way the UPS guy, who is not a yachtie, is on a first-name basis with your dog and knows all about the product lines carried by Defender.com

The Bible verse that may best approximate the current status of your restoration project is

1. Hebrews 11:7 (‘By faith Noah, divinely warned, built this ark to save his family’)
2. Ezekiel 15:3 (‘Is wood from this tree fit to make anything useful?’)
3. Luke 14:30 (‘This man began to build, and could not finish’)

Life lessons learned

One thing you’ve found out about yourself that you never expected is that

1. You’ve learned many new things and gained a priceless experience
2. You have physical strength and stamina you didn’t know you had
3. Falling sweat actually splashes

By now you are convinced that marine-toilet plumbing should be

1. Replaced every three years
2. Replaced by every new owner
3. Made of heliarc-welded and polished 3-inch schedule-40 type-316 stainless-steel pipe and never changed at all

One maintenance cycle you did not expect to need to know is that

1. Bottom paint, no matter how old, should be reapplied within two weeks of launching
2. Spars should be removed and inspected every three years
3. The screw threads on jackstands should be oiled annually

When your restoration project is complete, you will know your boat

1. Better than most yacht owners know their own boats
2. Enough to trust it in nearly any conditions
3. More intimately than you know your wife

Your restoration project has taken

1. More or less the amount of time you expected it would
2. A season longer than you expected
3. Several years longer than you expected

The one most likely to perform future major maintenance and repair on your boat is

1. A trusted yacht-service facility
2. The next owner
3. You

When the boat is finished